background image

 

 

6.3 ASH TRAY 1 AND ASH TRAY 2 CLEANING 

 

The ashtray 1 and ashtary 2 which is placed under or behind(according to the model) the 

firepot is easy-to-replace. When you pull them, they will be moved out easily. You should 

clean ash tray 1 daily, ash tray 2 once in 20 days. 

 

7. GENERAL WARRANTY AND POLICIES

 

 

ARAL

 

MAKİNA MADENİ EŞYA

 SA

N. VE TİC.LTD. ŞTİ 

  provides  warranty  to  the  buyer 

within the framework of legal provisions. 2 (two) year warranty period starts from the 

actual delivery date. An invoice must be presented for inclusion in the warranty. 
 
In case of any damage related to production in our product, our company will try to repair 

this  damage  as  soon  as  possible  within  the  warranty  period  or  it  will  replace  the 

problematic part. Only spare parts approved or supplied by the manufacturer must be 

used. 
After  the  warranty  period,  our  company  will  continue  to  serve  you  in  the  necessary 

conditions. 
You are kindly requested to inform the relevant dealer where you have purchased the 

product from with the model number printed on the label on the back of the product. 
The company reserves the right to make changes to the product after publication of this 

manual. 
Malfunctions resulting from the use of the product contrary to the matters stated in the 

user manual are not covered by the warranty 
 

Glass, cast irons, electric current high/low voltage resulted to a digital card failure, 
user errors are not covered by the warranty. 

Our  company is  not  responsible  for  any  damages  during  transport,  in  case    dealer  or 

manufacturer are not informed about itand  not presented the proof.

 

Our company is not responsible for any damage that may occur in case of any voltage 

drop or rise. 
Our company is not responsible for any damages in case user enters in system menu and 

change the parameters. 
The  damages can  be  occured  in case cleaning  and  maintenance  are  not  made are  not 

covered by the warranty.  
 
 
 

Summary of Contents for TP-05





















Reviews: