10
TEC-61201-1
Technical Manualе
PRIZRAK-510, 520 v7
Examples of programming
Example 1
Objective:
Change the factory settings of the Immobilizer. Set
Output 2 – Engine locking – to normally open relay control.
Execution:
1.
Turn the ignition on.
2.
Enter PIN code, wait for confirmation.
3.
Once the system has been powered, within 10 seconds enter
Menu 1 by pressing Programming button 10 times. If your
actions are correct, the Immobilizer will confirm it by 3 audible
signals.
4.
Select Option 3 – Engine locking – from Menu 1 by pressing
Programming button 3 times. The Immobilizer will acknowledge
the selection by a sequence of 3 audible signals.
5.
Enter Option 3 menu by pressing and holding the brake pedal.
The Immobilizer will indicate the setting by 2 repeated audible
signals since the current (factory) setting is normally closed
relay control.
6.
Select «normally open relay control». by pressing Programming
button 4 times. The Immobilizer will notify the selection of this
option by a single audible signal.
7.
Exit the programming mode by turning the ignition off.
Example 2
Objective:
Change the factory settings of the Immobilizer. Extend
the Anti HiJack activation distance from 100 to 300 meters.
Execution:
1.
Turn the ignition on.
2.
Enter PIN code, wait for confirmation.
3.
Once the system has been powered, within 10 seconds enter
Menu 2 by pressing Programming button 12 times. If your
actions are correct, the Immobilizer will confirm it by 4 audible
signals.
4.
Select Option 3 – AntiHiJack response delay – from Menu 2 by
pressing Programming button 3 times. Immobilizer will confirm
the selection by emitting a sequence of 3 audible signals.
5.
Enter Option 3 menu by pressing and holding the brake pedal.
The Immobilizer will inform you on the option setting by
repeated single audible signals because the current (factory)
setting is 1 (which stands for 100 meters distance).
6.
Adjust the setting of option 3 by pressing the Programming
button 2 times, i.e. increase the option value by 2 increments
(1 + 2 = 3). Immobilizer will acknowledge the selection by
emitting a sequence of 3 audible signals (i.e. 300 m).
7.
Exit the programming mode by turning the ignition off.
Resetting to factory default settings
There is a procedure of resetting the programmable settings, where all vehicle model settings are removed from Immobilizer’s permanent
memory while PIN code and all other programming options are returned to factory settings.
For vehicles with Immobilizer:
1.
De-energize the Immobilizer.
2.
Press and hold the integrated button (see «Immobilizer wiring
diagram»).
3.
While holding the button, energize the Immobilizer. The
Immobilizer will start emitting an intermittent audible sound.
4.
Release the button and wait for the audible signal to stop.
5.
Turn on the ignition. Enter PIN-code, a trill will be made.
6.
Wait for an intermittent signal meaning the system was reset
to factory default settings. Switch the power off.
For vehicles without Immobilizer:
Resetting can be done in three ways:
1.
using an integrated button if the default PIN «2» has not been
changed and the vehicle has not travelled more than 10 km
after installation.
2.
using the button and PUK.
3.
By installing the Alarm in the same vehicle as it was installed
4.
before (if you know the PIN-code).
Procedure for first two options:
1.
Press and hold the integrated button (see «Immobilizer wiring
diagram»).
2.
While holding the button, energize the Immobilizer. The
Immobilizer will start emitting an intermittent audible sound.
3.
Release the button and wait for the audible signal to stop.
4.
If the vehicle has travelled less than 10 km after installation,
and factory default PIN remained unchanged, it is allowed to
use PIN code “2” by pressing an integrated button. Otherwise
enter PUK. A trill will sound.
5.
Wait for an intermittent signal meaning the system was reset
to factory default settings. Switch the power off.
The protective layer can be removed and PUK can be entered
only by the registered user.
