10
Programming sequence
1
Turn the ignition on Enter the PIN code and wait for confirmation
(see PIN code entering section)
2 Enter Menu 2 by pressing and releasing the Programming but-
ton 12 times (start doing this no later than 10 seconds upon
PIN code entering). If all operations have been carried out cor-
rectly, the Immobilizer will inform on this fact by 4 audible
signals (see Programming menu table).
3 Beginning from point 4, programming algorithm is analogical
with the one described in Immobilizer hardware features con-
figuration (Menu 1), except for points 6.1, 6.2, 6.3.
PIN code changing
1 Turn the ignition on.
2 Enter the PIN code.
3 Press the Programming button 14 times. Wait for Immobilizer’s
confirmation by 1 audible signal.
4 Set the new PIN code by using any combination of buttons
perceived by the Immobilizer (see Integrator files). When
entering a new PIN code, each pressing perceived by the Im-
mobilizer is confirmed by the audible signal for further control
-
ling assistance.
5
Wait for confirmation by 1 audible signal.
6 Re-enter the new PIN code.
7
Wait for confirmation:
◊
2 audible signals and a sound trill mean that the PIN code
has been changed and the Immobilizer has left the PIN code
changing mode.
◊
Sound alert means that the PIN code has not been changed
and the Immobilizer has left the PIN code changing mode.
A mistake has been made when entering the new PIN code
confirmation and it is necessary to repeat the PIN code changing
procedure starting from p. 1.
You can exit the PIN code changing mode anytime by turning the ig-
nition off.
Programming button changing
1 Reset all settings to factory default.
2 Interface the Immobilizer with the vehicle.
3
If analog steering wheel buttons are used please define them
(see above for the description of this procedure).
4 In order to assign any of the buttons perceived by the Immo-
bilizer as the Programming button, press the selected button
and hold it for longer than 5 seconds until a long audible signal
will be heard.
Programming button can be assigned within 15 minutes
after Immobilizer interfacing with the vehicle.
Programming examples
Example 1
Objective:
You would like to change the factory settings of the Im-
mobilizer: set output No. 2 Engine locking to control the normally
open relay.
Execution:
1 Turn the ignition on.
2
Enter the PIN code and wait for confirmation.
3 Enter Menu 1 by pressing and releasing the Programming
button 10 times. If you have performed all the actions
correctly, the Immobilizer will notify you of it with 3 audible
signals.
4
According to Immobilizer hardware functions configuring
(Menu 1) option No. 3 Engine locking is to be selected. To do
so, press and release the Programming button 3 times.
The Immobilizer will inform you on the selected menu option
number by series of 3 audible signals.
5 Enter option No. 3 by pressing and holding the brake pedal.
The Immobilizer will inform you on the option setting
by repeated double audible signals because the current
(factory set) option setting is “normally closed relay control”.
6 Select “the normally open relay control” by pressing
and releasing the Programming button twice, for the second
setting is followed by the third. The Immobilizer will inform
you on the option setting with series of 1 audible signal.
7 Exit programming mode by turning the ignition off.
Example 2
Objective:
You would like to change the factory settings of the Im-
mobilizer: to increase the Anti HiJack activation distance from 100 to
300 meters.
Execution:
1 Turn the ignition on.
2
Enter the PIN code and wait for confirmation.
3 Enter the Immobilizer setting mode by pressing and releasing
the Programming button 12 times (start doing it no longer
than 10 seconds after entering the PIN code). If you have
performed all the actions correctly, the Immobilizer will notify
you of it with 4 audible signals.
4 Select the programming option for setting the Anti HiJack
activation distance. According to Table 1 “Immobilizer
settings” option No. 5 is to be selected. To do so, press
and release the Programming button 5 times. The Immobilizer
will inform you on the selected menu option number by series
of 5 audible signals.
5 Enter option No. 5 by pressing and holding the brake pedal.
The Immobilizer will inform you on the option setting
by repeated single audible signals because the current
(factory set) option setting is 1 (which stands for 100 meters
distance).
6 Change option No. 5 setting by pressing and releasing
the Programming button twice, therefore increasing
the option setting by 2 (1+2=3). The Immobilizer will inform
you on the option setting with series of 3 audible signals (300
meters).
7 Exit the setting mode by turning the ignition off.
Resetting to factory default settings
Immobilizer has a procedure of resetting the programmable settings,
where all vehicle model settings are removed from Immobilizer’s en-
ergy independent memory and PIN code and all other programming
options are returned to factory original values.
If certain or all menu options are password protected (see Immobi-
lizer user settings programming (Menu 2), p. 2), only the options that
are not prohibited will be reset. The remaining ones will keep their
current values.
In order to reset to factory default:
1 Remove power supply from Immobilizer
2 Press and hold the integrated Programming button
3 Connect the power supply while holding the button. Immobilizer
will emit irregular audible signals.
4 Release the button and wait until the signals stop.
5 Turn the ignition on and enter the current PIN code
*
.
6 An audible trill will be heard, which indicates that resetting
to factory default has been completed.
7 Remove the power supply and disconnect the Immobilizer
from CAN bus.
*
If the Immobilizer is not installed in the vehicle, please enter the PUK code
with the integrated Programming button.
