12
TEC-61231-23 Technical Manualе
PRIZRAK
Programming – Stage two
Programming the Alarm configuration
At stage two the Alarm hardware functions and user settings are changed, and a new PIN code is programmed.
Table 6. Programming menu
Name of the menu
Menu code
Number of
audio signals
Designation
Hardware features
configuration (Menu 1)
10
3
Configuration of the Alarm hardware settings
Configuration of
programmable inputs/outputs
(Menu 1.1)
11
6
Configuration of programmable inputs/outputs
User functions configuration
(Menu 2)
12
4
Configuration of the user settings
Set up shock sensors and tilt\
movement sensor
8
5
Adjustment of sensitivity of additional shock sensor; switching on/off
the tilt/displacement sensor
Remote start configuration
16
7
Menu is active only with ESM module installed or with remote start
digital output active
Heater configuration
17
8
Configuration of heater operating modes
Programming the Alarm hardware
The Alarm is programmed in accordance with "Hardware features configuration" table.
Table 7. Hardware features configuration
#
Option
Range
Factory default
settings
Notes
1
Vehicle model
–
–
–
2
Engine lock
1-4
2
1 – control of a normally open relay;
2 – control of a normally closed relay;
3 – acceletator pedal lock (force to stop);
4 – starter motor lock
3
Safe lock
1-3
1
1 – Engine will be locked regardless of speed;
2 – if speed is 30km\h or lower;
3 – on complete stop
4
Type of external buttons
1-2
–
1 – analogue buttons; 2 – digital buttons.
Inputs #7 and #16 (connector Х1,18-pin)
5
Control of the factory
security system
1-2
On
1 – on
2 – off
6
Sequential door opening
1-2
Off
1 – on
2 – off
7
Hazard lights control algorithm
1-5
–
1 – pulse negative; 2 – status negative;
3 – pulse positive; 4 – status positive;
5 – lights control (negative)
8
Central lock alternative
control algorithm
1-3
–
1 – single wire pulse negative; 2 – single wire pulse negative
(if central lock state if unavaliable);
3 – two wire pulse negative
9
Siren control/Horn control
1-2
1
Selecting operating mode and polarity of
output #17.
1 – Siren control. Emitting of a constant level signal (+12V).
2 – Horn control. Emitting of an intermittent negative
signal. Controls the original horn of the vehicle
10
Time interval of Timer
Channel (Comfort) feature
1-6
3
One unit equals 10 seconds.
11
External sensors multiplex mode
1-2
1
1 – multiplex operating mode of external sensors
2 – standard operating mode of external sensors
12
Engine start lock
1-2
2
1 – on
2 – off
13
Parking system control
algorithm (activation)
1-3
1
1 – by reverse gear; 2 – by speed;
3 – by reverse gear with an override
14
Parking system control button
–
–
It is possible to assign CAN bus recognized button,
analog button or digital button (positive/negative)
15
Speed control
1-2
1
1 – on
2 – off
16
Brake presses
1-7
3
–
17
GSM lock
1-2
2
1 – on (GSM interlock disabled)
2 – off (GSM interlock enabled)
18
Car battery warning threshold
1-15
8 (11,3)
1 – 10.6 V … 15 – 12 V
19
–
–
–
–
20
–
–
–
–
21
RFID tag
1-4
1
1 – not in use; 2 – RFID check when disarming; 3 – factory
remote lock; 4 – factory remote lock in high risk locations
