17
TEC-61231-23 Technical Manualе
PRIZRAK
Heater configuration
Table 12. Heater configuration
#
Function
Setting
range
Factory
default
settings
Description
1
Accept/Decline operation of
an aftermarket heater
1-2
1
1 – on
2 – off
2
Heater operation in preheating mode
1-2
2
1 – on
2 – off
3
Heater management protocol
1-3
–
1 – Webasto
2 – Eberspacher
3* – not preset (automatic)
4
Heater shutdown conditions
1-3
1
1 – time only
2 – engine temperature only
3 – time and temperature
5
Heater operation time
1-12
3
One unit equals 10 minutes (10 to 120 minutes)
6
Engine temperature level
to turn off the heater
1-7
5 (50
°С)
1 –
0°С
... 7 –
70°С
7
Battery power level to
turn off the heater
1-11
9 (11.3 V)
1 – 10.5 V … 11 – 11.5 V
8
Accept/Decline operation of a
factory heater via CAN bus
1-2
1
1 – on
2 – off
9
Code to switch heater on
with factory buttons
–
–
You can program a code to switch on or off heater with factory
buttons. Programming is done the same way as PIN code. Code
can be entered only when the is ignition on.
10
Heater control with the factory remote
1-2
2
1 - on
2 - off
11
Control of an aftermarket
heater algorithm
1-2
1
1 - status control
2 - impulse control
Programming sequence
1.
Turn the ignition on.
2.
Follow through with identity verification sequence.
3.
Press the Programming button 17 times: the Alarm will emit 8
audio and light signals;
4.
Select menu option by pressing and releasing the Programming
button the number of times matching the number of option.
The Alarm will confirm the option number by a series of audio
and light signals.
5.
Go to option setting by pressing and holding the brake pedal.
The Alarm will notify of the option status by a series of audio
and light signals of a changing duration.
6.
Adjust option settings by pressing the Programming button
the number of times matching the number of steps from the
current status to the required one. The Alarm will confirm the
selected function by audio and visual signals. Please remember
that from the last function the program will go to the first one.
7.
The Alarm will exit the settings mode and save all configuration
settings in energy independent memory when the ignition is
turned off while brake pedal is released or within 10 seconds
after last menu action if the brake pedal is released.
Remote start configuration
Table 13. Engine remote start configuration
№
Function
Range
Factory
default
Note
1 "Hands free" in remote start mode
1 – 2
2
1 – enabled; 2 – disabled
2
ESM-250 configuration
1 – 16
–
Detected automatically. Set up manually if required
3 "Keep running" feature
1 – 2
2
1 – enabled; 2 – disabled
4 "Keep running" feature operation time
1 – 12
2
1 – 10 min.; ... 12 – 120 min.
5 "Turbotimer" feature
1 – 2
2
1 – enabled; 2 – disabled
6 External temperature sensor
1 – 2
2
1 – temperature sensor; 2 – interior temperature sensor
7 Ignore brake on engine start
1 – 2
2
1 – brake pedal will be ignored ; 2 – pressed brake
pedal will prevent the engine from launching
8 Shut down engine by releasing brake pedal
(in remote start)
1 – 2
2
1 – enabled; 2 – disabled
9 Brake state in CAN
1 – 2
2
1 – enabled; 2 – disabled
10 Turn off the engine of disarming
1 – 2
2
1 – enabled; 2 – disabled
11 Engine shutdown conditions
1 – 3
1
1 – by time; 2 – by engine temperature;
3 – by time or engine temperature
12 Engine type
1 – 3
1
1 – diesel; 2 – gasoline; 3 – hybrid
13 Starter delay (only for diesel engines)
1 – 4
1
1 – 5 sec; ...4 – 20 sec
14 Idle RPM
1 – 6
–
1 – 600 rpm.; ...6 – 1100 rpm. Detected automatically.
Set up manually if required
15 Engine runtime in remote start
1 – 12
3
1 – 10 min.; ... 3 – 30 min.; ...12 – 120 min.
16 Engine shutdown temperature in remote start
1 – 14
12
1 – "15 °С"; 2 – "20 °С"; ... 12 – "70 °С";
... 14 – "80 °С"
17 Temperature to launch the engine by temperature
1 – 8
1
1 – "-30 °С"; 2 – "-20 °С"; 3 – "-15 °С"; 4 – "-10 °С";
5 – "-5 °С"; 6 – "0 °С"; 7 – "5 °С"; 8 – "10 °С"
