20
TEC-61231-23 Technical Manualе
PRIZRAK
Programming example
Example 1
Objective: You would like to change the factory settings of the
Alarm and set output #2 Engine lock to control the normally open relay
.
Sequence:
1.
Turn the ignition on.
2.
Enter PIN code and wait for confirmation.
3.
Enter Menu 1 by pressing and releasing the Programming
button 10 times. If you have performed all the actions correctly,
the Alarm will notify you with 3 audio and light signals.
4.
According to
"
Menu 1
"
, select option 2 – Engine lock – by
pressing the Programming button 2 times. The Alarm will
inform you about chosen menu option number by a series of 2
audio and light signals.
5.
Enter option 2 by pressing and holding the brake pedal. The
Alarm will show option setting by a repeated double audio and
light signals because the current (factory set) option setting is
normally closed relay control.
6.
Select the normally open relay control by pressing and releasing
the Programming button 3 times. The Alarm will inform you
about chosen menu option with series of 1 audio signal.
7.
Exit programming mode by turning the ignition off.
Example 2
Objective: You would like to change the factory settings of the
Alarm and increase AntiHiJack distance from 100 to 300 meters
Sequence:
1.
Turn the ignition on.
2.
Enter PIN code and wait for confirmation.
3.
Enter Menu 2 by pressing and releasing the Programming
button 12 times. If you have performed all the actions correctly,
the Alarm will notify you with 4 audio and light signals.
4.
According to
"
Menu 2
"
, select option
#3
"
Distance for enabling
"
AntiHiJack
"
, by pressing the Programming button 3 times. The
Alarm will inform you about chosen menu option number by a
series of 3 audio and light signals.
5.
Enter option 2 by pressing and holding the brake pedal. The
Alarm will show option setting by a repeated double audio and
light signals because the current (factory set) option setting —
"
1
"
(100 meters).
6.
Change option
#3,
to do so press brogramming button 2 times,
i.e. increase setting by 2 (1 + 2 = 3). The Alarm will inform you
about chosen menu setting with by a series of 3 audio and light
signals (300 meters).
7.
Exit programming mode by turning the ignition off.
Reset to the factory default settings
The Alarm has a procedure of resetting the programmable settings, when all settings of the vehicle model are removed from the Alarm
permanent memory, and PIN code and all other programming options are returned to factory set values.
To reset to the factory default settings
if the Alarm is installed:
6.
Disconnect power supply from the Alarm.
7.
Press and hold the built-in button (see
"
Connection scheme
"
).
8.
Connect the power supply while holding the button. The Alarm
will emit dashed audio signal.
9.
Release the button and wait until the dashed signal stops.
10.
Turn on the ignition. Enter PIN-code, a trill will be made.
11.
A signal will notify you that the Alarm was reset to factory
default settings.
12.
Disconnect the power source and CAN bus from the alarm.
If the Alarm was not installed in the vehicle:
There are 3 ways to reset the alarm:
1.
With built-in button, if factory PIN-code (
"
2
"
) was not changed
and vehicle was driven for less then 10 kilometers.
2.
With built-in button and PIN-code.
3.
By installing the Alarm in the same vehicle as it was installed
before (if you know the PIN-code).
Sequence (for the first two ways):
1.
Press and hold the built-in button.
2.
Connect the power supply while holding the button. The Alarm
will emit dashed audio signal.
3.
Release the button and wait until the dashed signal stops.
4.
If the vehicle was not driven for more then 10 kilometers,
enter PIN-code
"
2
"
with built-in button. Otherwise enter PUK-
code with the built-in button. A trill will be made.
5.
A signal will notify you that the Alarm was reset to factory
default settings.
6.
Disconnect the power source.
Only owner of the system should scratch PUK-code and enter
it .
Figure 2
