1. Display -current temperature/humidity
2. Button
3. Menu button
4. Button
Current temperature is displayed on the screen. Use the Menu button (in
the middle) to display current humidity.
1. Sun icon
2. Humidity icon
3. Current humidity
4. Control light
DESCRIPTION
The F-2z v1 room regulator is intended for controlling the heating
device. Its main task is to maintain the pre-set room temperature by
sending a signal to the heating device when the room temperature has
been reached.
Two colour versions are available: black and white.
Controller assets:
•
large, easy-to-read display
•
front panel made of glass
•
built-in temperature and humidity sensor
•
intended to be mounted in a frame
HOW TO INSTALL
The regulator should be installed by a qualified person.
WARNING
•
Risk of fatal electric shock from touching live connections.
Before working on the controller switch off the power
supply and prevent it from being accidentally switched on.
•
Incorrect connection of wires may damage the regulator!
How to install particular elements:
The diagram below illustrate how particular the regulator should be
mounted:
HOW TO CHANGE THE
PRE-SET TEMPERATURE
The pre-set zone temperature may be adjusted in the EU-F-2z v1 room
regulator by means of buttons
and
.
During inactivity, the screen displays current temperature. Press one of
the buttons
or
to display the pre-set temperature value - the
digits start flashing. Use the buttons
to adjust the value.
When a sun icon appears next to the temperature value, it means that
the pre-set room temperature has been reached and heating has been
disabled. If the sun icon is flashing, the room is being heated and the
pre-set temperature hasn’t been reached yet.
22
.3
1
3
4
2
1
2
3
4
4. Auto-lock
The „Loc” function enables the user to activate the key lock.
Select Loc and when the screen starts flashing, press the Menu
button. Next, the regulator asks if you want to activate the key
lock (YES/NO). Select YES using one of the buttons
or
. Wait 5
seconds to confirm. When the lock is active, the keys are locked after a
few seconds of inactivity. To unlock, press and hold both buttons
and
. When the screen displays Loc, select this option again and change
it to NO.
5. Min/Max pre-set temperature
This function enables the user to define the minimum
(T1) and the maximum (T2) value of the pre-set room
temperature. Select this function and when the screen
starts flashing, press the Menu button. Use the buttons
or
to
adjust the value. In order to confirm changes, wait for about 5 seconds
or press the Menu button.
6. Factory settings
The „Def” function enables the user to restore factory settings.
Select this function and when the screen starts flashing, press
the Menu button. Next, the regulator asks if you want to restore
factory settings (YES/NO ). Select the answer using one of the buttons
or
. In order to confirm, wait for about 5 seconds or press the
Menu button.
7. Exit the menu
To exit the menu, select the Ret option. The screen flashes for 3
seconds and exits the menu.
NOTE
In order to display the software version number, press and hold the
button located on the right side of the regulator.
MENU FUNCTIONS
Press and hold the Menu button to enter the regulator menu. Use the
buttons
and
to navigate through menu functions.
1. Operation mode
The „Out” function enables the user to choose one of the
regulator operation modes: heating (HEA) or cooling (Coo).
Select Out and when the screen starts flashing, press the Menu
button. The screen shows available operation modes (Coo, HEA). Use
the buttons
or
. to select the mode. In order to confirm changes,
wait for about 5 seconds or press the Menu button.
2. Histereza
The „His” function enables the user to set the room temperature
hysteresis within the range of 0,2°C to 4°C. Room temperature
hysteresis defines the pre-set temperature tolerance in order
to prevent undesired oscillation in case of small temperature fluctuation.
Example: Pre-set temperature : 23°C Hysteresis: 1°C
The room regulator reports that the temperature is too low when the
room temperature drops to 22 °C. In order to define the pre-set
temperature hysteresis, use the buttons
or
and select a desired
value. In order to confirm changes, wait for about 5 seconds or press the
Menu button.
3. Calibration
The Cal function enables the user to calibrate the sensor within
the range of -10°C to +10°C. Select Cal and when the screen
starts flashing, press the Menu button. The screen displays
current calibration value. Use the buttons
and
to adjust the
value.
The regulator is intended to be mounted in a frame. It fits in the
following frames:
Ospel - Sonata
Berker - S.1, B.1, B.3, B.7
Jung - AS, A500, A PLUS, A CREATION
Gira- STANDARD 55, E2, EVENT, ESPRIT, PROFIL55, E22
Kopp - ALASKA
Elko - RS16, PLUS
22
.3
55 mm
71 mm
55
mm
71
mm
~
N
L
NO
COM
