background image

TECH

 

 

15 

 

 
 

 

 
 

EU Declaration of conformity 

 

Hereby,  we  declare  under  our  sole  responsibility  that  EU-RI-1  manufactured  by  TECH  STEROWNIKI,  head-
quartered in Wieprz Biała Droga 31, 34-122 Wieprz, is compliant with Directive 2014/35/EU of the European 
Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of Member States relating 
to the making available on the market of electrical equipment designed for use within certain voltage limits 
(EU OJ L 96, of 29.03.2014, p. 357), Directive 2014/30/EU of the European Parliament and of the Council of 26 
February 2014 on the harmonisation of the laws of Member States relating to electromagnetic compatibility 
(EU OJ L 96 of 29.03.2014, p.79), Directive 2009/125/EC establishing a framework for the setting of ecodesign 
requirements for energy-related products as well as the regulation by the MINISTRY OF ENTREPRENEURSHIP 
AND TECHNOLOGY of 24 June 2019 amending the regulation concerning the essential requirements as regards 
the restriction of the use of certain hazardous substances in electrical and electronic equipment, implementing 
provisions of Directive (EU) 2017/2102 of the European Parliament and of the Council of 15 November 2017 
amending Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and 
electronic equipment (OJ L 305, 21.11.2017, p. 8). 
 

For compliance assessment, harmonized standards were used: 

 PN-EN IEC 60730-2-9:2019-06, PN-EN 60730-1:2016-10. 

 

 

 

Wieprz, 24.02.2022 

 

 

 

 

 

Summary of Contents for EU-RI-1

















Reviews: