background image

TECH

III.d) Protection against boiling water in the boiler

This   protection   prevents   high   temperature   to   appear   in   the 

boiler (

only during using the function: boiler’s priority

). When the 

set on the boiler tempertaure equals 55 degrees Celsius and the actual 
temperature in the boiler equals 62 C, the feeder and the fan are turned 
off.  When the temperature increases to 80 C,  CH pump is  turned on. 
When the temperature still continues to increase, when it reaches 85 C 
alarm   is   turned   on.   Described   situation   may   appear   when   boiler   is 
damaged or faulty, the sensor is installed in the wrong way, or the pump 
has a fault. However, if the temperature decreases, when it drops to 60 C 
the regulator will turn the feeder and the fan on and it will work until 
reaching the set on the boiler temperature.

III.e) Temperature Safety Protections

The regulator is equipped in an additional protection in the case of 

faulty bimetallic sensor: alarm is turned on and an adequate message is 
projected on the screen after the tempertaure of 95 degrees is exceeded:

III.f) Fuel Feeder Protection

The   worm   in   the   fuel   feeder   is   equipped   in   an   additional   sensor 

measuring   temperature.   Alarm   is   turned   on   when   the   temperature 
increasea   significantly   (above   65   C):   the   feeder   is   turned   on   for   10 
minutes in order to move the fuel to the combustion chamber. The sensor 
in the worm prevents the fuel from burning in the basket.

III.g) Fuse

The   regulator   is   equipped   in   tubular   fuse-element   WT   6.3A,   that 

protects the system.

- 15 -

A LA R M
BasketSen Failure

A L A R M
TOO HIGH TEMP

Summary of Contents for ST-77





















Reviews: