background image

TEP-0500-IMX7 HARDWARE MANUAL 

– VER 1.00 – AUG 03 2018 

Page 

11

 of 

27

 

2.5. Internal Board Connectors 

 
The TEP-0500-IMX7 has several connectors, switches and internal expansion options. It is necessary to 
remove the Power Expansion module to access several switches, headers and connectors. 
Rear view (opened device) with the Power Expansion module: 
 
                                                                                                                                                             

                                                                                                                
                                                                                                                
                                                                                               A              
                                                                                                                
                                                                                                                
                                                                                                           
                                                                                                                
                                                                                                             
                                                  

Power Expansion Module

                             

                                                                                                                
                                                                                                              
                                                                                                                
                                                                                                              
                                                                                                                 
                                                                                                                 

                                                                                                                 

 

 

Internal Connectors and Switches: 
 

No. 

Description 

No. 

Description 

RTC Battery connector  

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for TEP-0500-IMX7




























Reviews: