5.Input Selector:
Use this button to switch between all the inputs.
6.Audio Function:
Use this to switch among treble, bass, balance & master volume control mode, then
use the master volume knob to adjust the corresponding sound effect.
7.Previous Track Button:
Press this button to go back to the beginning of the previous track on either the iPod™
(Classic and Nano), USB flash drive,SD Card or bluetooth. In tuner mode, press this button and hold for several
seconds to scan stations from the current frequency to the lowest frequency. The scan will not pause until the
unit finds a strong enough frequency. To save a specific frequency (station), go to the station and then press the
“RPT/RDM” button on the face of unit or the “RPT” key on the remote control and then using the number keys
enter a number for the saved station. The number entered should be between1 and 30. After entering the
numbers, press the “RPT/RDM” button or “RPT” key again to save. And the unit will exit the scan and play the
station stored.
8.Next Track Button:
Press this button to go back to the beginning of the next track on either the iPod™
(Classic and Nano), USB flash drive,SD Card or bluetooth.In tuner mode,press this button and hold for several
seconds to scan station from the current frequency to the highest frequency.The unit will not pause the scan
untill the unit finds a strong enough frequency. To save a specific frequency (station), go to the station and then
press the “RPT/RDM” button on the face of unit or the “RPT” key on the remote control and then using the
number keys enter a number for the saved station. The number entered should be between1 and 30. After
entering the numbers, press the “RPT/RDM” button or “RPT” key again to save. And the unit will exit the scan
and play the station stored.
9.AM/FM Selector:
Press this button to switch the inputs between the FM and AM.
10.Speaker A/B:
Press this button to switch the output speakers among Group A, Group B and Group A&B.
11.BLUETOOTH Indicator:
When the unit is turned on, the bluetooth function will be activated. This indicator
will flash when there is a bluetooth enabled device (ie cellphone) pairing with the unit. When the unit is
connected to the Bluetooth enabled device, the indicator will remain illuminated.
12.Infrared Sensor:
This infrared sensor is designed to receive the signal from remote control. Do not obstruct
the infrared sensor to ensure the remote control operates optimally.
13.SUB OUT:
Use this knob to adjust the subwoofer output volume.
14.PRE OUT:
Use this knob to adjust the pre-amp volume output in addition to the master volume control.
15.MASTER Volume
:Use this knob to adjust the master volume output.
16.USB Input:
Insert your USB flash drive or iPod™(Classic and Nano) into this slot. The unit will only
read .mp3, .wav, .wma files from the USB flash drive or iPod™(Classic and Nano).The maximum storage
size of the USB flash drive cannot exceed 32GB. Make sure to set the input selector button (5) to “USB”
to play the signal from the USB flash drive or iPod™(Classic and Nano). When the unit is playing tracks
from the USB flash drive the track and elapsed time will display on the screen.
17.Headphone Output:
Connect your headphone here. Make sure the volume level of the unit is turned down
before making the connection.
18.MIC1:
Microphone Input ¼".
19.MIC2:
Microphone Input ¼".
20.SD Card Input:
Insert your SD card into this slot. The unit will only read .mp3, .wav, .wma files from SD
card. The maximum storage size of the SD card cannot exceed 32GB. Make sure to set the input selector
button to “SD CARD” to play the signal from the SD Card. When the unit is playing tracks from the SD Card
the track and elapsed time will display on the screen.
21.Microphone Volume:
Use this knob to adjust the volume of the microphones.
23.Microphone Bass Control:
Use this knob to adjust the microphone’s bass.
24.Microphone Treble Control:
Use this knob to adjust the microphone’s treble.
24.Microphone ECHO:
Use this knob to adjust the microphone’s echo.
Hybrid Series
