RUN 600 XTPRO: Service & Maintenance Manual - rev. 1.3
Page 6.28
•
For versions with speed expressed in km/h:
Speed
(Km/h)
PWM signal
(Vdc)
Analog signal
(Vdc)
Frequency
(Hz)
CPU board
Inverter interface board
Inverter
Display
6-3/CN1
10-3/CN2
5-6/CN1
L-O
Display
2.0 4.42 4.42 1.09 1.09 11.0
5.0 3.51 3.51 2.73 2.73 27.3
9.0 2.30 2.30 4.89 4.89 49.3
12.6 1.20 1.20 6.85 6.85 69.0
16.0 0.17 0.17 8.70 8.70 87.6
Table 6.7-1
•
For versions with the speed expressed in mph:
Speed
(mph)
PWM signal
(Vdc)
Analog signal
(Vdc)
Frequency
(Hz)
CPU board
Inverter interface board
Inverter
Display
6-3/CN1
10-3/CN2
5-6/CN1
L-O
Display
1.0 4.48 4.48 0.88 0.88 8.7
3.0 3.52 3.52 2.61 2.61 26.3
5.0 2.70 2.70 4.35 4.35 43.9
7.0 1.61 1.61 6.09 6.09 61.6
9.0 0.65 0.65 7.82 7.82 79.3
Table 6.7-2
Obviously, the voltages and frequencies quoted above are nominal values.
For the Hitachi J100 inverter, the data given in the above tables will be slightly
different, but still comparable.
(4)
Place the tester probes between the terminals O (signal) and L (ground) of the inverter. Check
that during machine operation the speed shown on the display and the voltage measured on
the inverter correspond to the values shown in Table 6.7-1 or in Table 6.7-2.
(5)
Place the tester probes between pins 5 (signal) and 6 (ground) of connector CN1 on the
inverter interface board. Check that during machine operation the speed shown on the display
and the measured voltage correspond to the values shown in Table 6.7-1 or in Table 6.7-2.
(6)
Place the tester probes between pins 10 (signal) and 3 (ground) of connector CN2 of the
inverter interface board. Check that during machine operation the speed shown on the display
and the measured voltage correspond to the values shown in Table 6.7-1 or Table 6.7-2.
(7)
Place the tester probes between pins 6 (signal) and 3 (ground) of connector CN1 on the CPU
board. Check that during machine operation the speed shown on the display and the measured
voltage correspond to the values shown in Table 6.7-1 or in Table 6.7-2.
Summary of Contents for RUN 600 XTPRO
