TOP 600 XTPRO: Service & Maintenance Manual - rev. 2.0
Page ii
7.7.
D
ISASSEMBLING THE CARDIO RECEIVER
........................................................................................................... 7.7
7.8.
D
ISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS
......................................................................................... 7.8
7.9.
D
ISASSEMBLING THE ALTERNATOR
.................................................................................................................. 7.9
7.10.
D
ISASSEMBLING THE BELT
............................................................................................................................. 7.10
7.11.
D
ISASSEMBLING THE CHAIN
........................................................................................................................... 7.12
7.12.
D
ISASSEMBLING THE PULLEY
......................................................................................................................... 7.13
7.13.
D
ISASSEMBLING THE PRIMARY SHAFT
............................................................................................................ 7.14
7.14.
D
ISASSEMBLING THE SADDLE AND STEM GUARD
............................................................................................ 7.15
7.15.
D
ISASSEMBLING THE HANDLES
....................................................................................................................... 7.16
7.16.
D
ISASSEMBLING THE ALTERNATOR BRUSHES
................................................................................................. 7.17
8.
ADJUSTMENTS.................................................................................................................................................... 8.1
8.1.
B
ELT ALIGNMENT
............................................................................................................................................. 8.1
8.2.
B
ELT TENSION
.................................................................................................................................................. 8.2
8.3.
C
HAIN ALIGNMENT
........................................................................................................................................... 8.3
8.4.
C
HAIN TENSION
................................................................................................................................................ 8.4
8.5.
P
LAY OF SADDLE STEM
..................................................................................................................................... 8.5
8.6.
W
EAR OF BRUSHES
........................................................................................................................................... 8.6
9.
CONFIGURING THE MACHINE ...................................................................................................................... 9.1
9.1.
U
SER SETTING PARAMETERS
............................................................................................................................. 9.1
9.1.1.
Language used .................................................................................................................................. 9.1
9.1.2.
Measurement system ......................................................................................................................... 9.1
9.1.3.
Maximum time................................................................................................................................... 9.2
9.1.4.
Activating the “+” and “
−
” keys...................................................................................................... 9.2
9.1.5.
Disabling the function keys ............................................................................................................... 9.2
9.1.6.
Enabling the “ENTER” key .............................................................................................................. 9.3
9.1.7.
Setting the priority ............................................................................................................................ 9.3
9.2.
T
ECHNICAL SETTING PARAMETERS
................................................................................................................... 9.3
9.2.1.
Enabling use of the hand sensor ....................................................................................................... 9.3
9.2.2.
Enabling the display mode................................................................................................................ 9.4
9.3.
M
AINTENANCE INFORMATION
.......................................................................................................................... 9.4
9.3.1.
Hours on ........................................................................................................................................... 9.4
9.3.2.
Hours of use ...................................................................................................................................... 9.4
9.4.
C
HANGING THE MAINTENANCE INFORMATION
.................................................................................................. 9.5
9.4.1.
Hours on ........................................................................................................................................... 9.5
9.4.2.
Hours of use ...................................................................................................................................... 9.5
10.
SCHEDULED MAINTENANCE ....................................................................................................................... 10.1
10.1.
E
XTERNAL CLEANING OPERATIONS
................................................................................................................ 10.1
10.1.1.
Setting up the operation .................................................................................................................. 10.1
10.1.2.
Cleaning operations ........................................................................................................................ 10.1
10.2.
R
OUTINE MAINTENANCE OPERATIONS
............................................................................................................ 10.2
10.2.1.
Setting up the operation .................................................................................................................. 10.2
10.2.2.
Cleaning operations ........................................................................................................................ 10.2
10.3.
S
PECIAL MAINTENANCE OPERATIONS
............................................................................................................. 10.3
10.3.1.
Setting up the operation .................................................................................................................. 10.3
10.3.2.
Checking the working conditions .................................................................................................... 10.3
10.3.3.
Performing the routine maintenance procedure ............................................................................. 10.3
10.3.4.
Checking the wiring and connections.............................................................................................. 10.3
10.3.5.
Checking the display ....................................................................................................................... 10.3
10.3.6.
Checking the state of wear of the chain........................................................................................... 10.4
10.3.7.
Lubrication ...................................................................................................................................... 10.4
10.3.8.
Checking the state of wear of the alternator belt ............................................................................ 10.4
10.3.9.
Checking the play of the saddle stem .............................................................................................. 10.4
10.3.10.
Checking the operation of the cardio receiver ................................................................................ 10.4
10.3.11.
Checking the resistance setting ....................................................................................................... 10.4
10.3.12.
Checking the noise of the brushes ................................................................................................... 10.4
Summary of Contents for Top 600 XTPRO
