Available users and default codes
User
User ID
Default Code
Manager
N/A
1-2-3-4-5-6
Users 1-8
1-8
Deleted
– Must be added by
the Manager
User 9
9
Deleted
– Must be added by
the Manager. User 9 is the
time delay override user.
Default codes must be changed immediately. All codes
contain 6 digits.
Acoustic and visual signals
The lock system will indicate status with beeps and LED
flashes on the keypad.
Signal
Indication
Short beep & LED flash
Button pressed correctly
Double beep & LED flash
Code or function entered
correctly
Long beep
Code or function entered
incorrectly
Remote blocking is active
LED flash every 2 seconds
The lock is in time delay
LED flash every second
and beep every other
second
The lock is in the open window
LED flash every 10
seconds
The lock is in penalty
3 short beeps every 3
seconds at opening
Low battery warning
Command Keys
All of the functions available to the manager and users
are accessible using command keys. To use a
command key, press and hold the relevant command
key until a double beep has sounded and the LED stays
on, enter a valid code then follow the remaining
instruction.
Key
Function
0
Change Code
1
Add a user
2
Disable all users / enable all users
3
Delete a user
5
Test the keypad buttons
7
Audit user status / download audit
9
Enter time delay values
Codes & Users
The manager code holder can:
Open the lock
Add, enable/disable and
delete users
Change code
Audit the lock
Set time delay values
There are 8 user codes numbered 1-8. Users can:
Open the lock
Change code
There is 1 user code numbered 9. User 9 can:
Open the lock if time delay
has been started by another
user
Open the lock if time delay is
not active
Change code
To open the lock
Enter a valid 6 digit code. Within 4 seconds, turn the
safe handle and/or turn the keypad.
To close the lock
Turn the safe handle and/or turn the keypad.
To open the lock when time delay is active
Enter a valid 6 digit code. Wait for the time delay
period to elapse.
The open window will be indicated with an LED flash
every second, and beep every other second.
Enter a valid 6 digit code. Within 4 seconds, turn the
safe handle and/or turn the keypad.
If user 9 is installed, the user is able to override time
delay started by another user.
To change code
Codes should always be changed and tested with the
safe or vault door open, with the bolt in the locked
position.
Press and hold 0 until a double beep sounds
Enter the old code, a double beep will sound
Enter the new code, a double beep will sound
Enter the new code again to confirm, a double beep
will sound
Test that the new code works whilst the door is open.
To test the keypad
If a key does not sound or if correct codes appear to be
invalid, a keypad test can be undertaken.
Press and hold 5 until a double beep sounds
Press each number key in turn.
A double beep will sound if a key is operating correctly,
a long beep will sound if a key is faulty. Contact a safe
engineer if a key is faulty.
To add a user (Manager only)
If a user is deleted, the user can be activated with a
new code.
Press and hold 1 until a double beep sounds
Enter the manager code, a double beep will sound
Enter a user ID number from 1-9. A double beep will
sound (If a double beep sounds and the LED turns
off, that user is already activated and can be
deleted)
The user should enter their 6 digit code, a double
beep will sound.
The user should enter their 6 digit code again to
confirm, a double beep will sound.
The user should check the code to ensure correct entry
whilst to door is open.
User 9 can only be activated if time delay is not in
operation or during the open window if time delay is in
operation.
