background image

9

a) a BMS reset: The battery has suffered damage (internal short circuit) or the connected circuitry is not allowing 
the BMS pulse to be delivered to the battery. 
b) STEP 3 - TEST BEFORE CHARGE - Temperature measured is below -20°C / -4*F. LiFePO4 batteries will suffer 
damage if charged below this temperature. 
c) STEP 4 SAVE mode: The charger has sensed that the battery is not accepting charge as expected. 

Try once 

more and if the result repeats, do not charge again! A professional assessment is required. 

d) STEP 9: TEST AFTER CHARGE -  the voltage reduced below 12.8V within the first 30 minutes, indicating the 
battery cannot hold charge and may be damaged. A  professional assessment is required.

 

More information on OptiMate TEST or MONITOR products can be found at www.optimate1.com.

MAINTAINING A LITHIUM BATTERY FOR EXTENDED PERIODS: 

A LiFePO

4

 battery can be left connected to the 

OptiMate Lithium for any extended period of time. The OptiMate Lithium maintenance program is fully 
automatic, it continuously monitors the battery voltage and delivers current only if it sensed the battery has lost 
charge (possibly through connected vehicle or other circuitry or self discharge). The OptiMate Lithium's 
maintenance program guarantees the battery will remain at or close to full charge, but never overcharged.

ECO POWER SAVING MODE WHEN THE CHARGER IS CONNECTED TO AC SUPPLY: 

The power converter switches to ECO mode when the charger is not connected to a battery resulting in a very 
low power draw of less than 0.5W, equivalent to power consumption of 0.012 kWh per day. When a battery is 
connected to the charger power consumption depends on the current demand of the battery and its connected 
vehicle / electronic circuitry. After the battery has been charged and the charger is in long term maintenance 
charge mode (to keep the battery at 100% charge) the total power consumption is estimated to be 0.024kWh or 
less per day.

LIMITED WARRANTY 

TecMate (International) SA, B-3300 Tienen, Belgium, offers this limited warranty to the original purchaser at retail of this product. 
This limited warranty is not transferable. TecMate (International) warrants this battery charger for three years from date of 
purchase at retail against defective material or workmanship. If such should occur the unit will be repaired or replaced at the option 
of the manufacturer. It is the obligation of the purchaser to forward the unit together with proof of purchase (see NOTE), 
transportation or mailing costs prepaid, to the manufacturer or its authorized representative. This limited warranty is void if the 
product is misused, subjected to careless handling, or repaired by anyone other than the factory or its authorized representative. 
The manufacturer makes no warranty other than this limited warranty and expressly excludes any implied warranty including any 
warranty for consequential damages. 
THIS IS THE ONLY EXPRESS LIMITED WARRANTY AND THE MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES ANYONE TO 
ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN THIS EXPRESS LIMITED WARRANTY. YOUR 
STATUTORY RIGHTS ARE NOT AFFECTED.
NOTE: Details at www.tecmate.com/warranty.

copyright © 2018 TecMate International

WARRANTY in Canada, USA, Central America and South America: 

TecMate North America, Oakville, ON, Canada, as a wholy owned subsidiary of TecMate International, assumes the responsibility 
for product warranty in these regions.
More information on TecMate products can be found at 

www.tecmate.com

.

Summary of Contents for Optimate M276










Reviews: