background image

7

Replacing the light bulbs

1.

Switch off the extractor hood and pull
out the mains plug or switch off the 
electricity supply at the fuse box.

2.

Remove the grease filters (see Filters and
Maintenance).

3.

Press down the bulb cover and 
disconnect from the light strip.

4.

Replace the light bulb (commercially
available candle bulbs, max. 40 watt,
E14 base). 

5.

Attach the lamp cover again.

6.

Re-insert the grease filters.

7.

Plug the appliance into the mains or
switch it on at the fuse box.

Cleaning and care

Disconnect the extractor hood from the
electricity supply by pulling out the
mains plug or switching it off at the fuse
box.

At the same time as you clean the 
grease filters, clean off any grease from
all accessible parts of the housing. This
significantly reduces the fire hazard and
ensures that the extractor hood 
performs as effectively as possible.

Use a hot detergent solution or a mild
window cleaner to clean the canopy of
the extractor hood.

Do not scrape off any dirt that has dried
on but loosen it up with a damp cloth.

Do not use abrasive cleaning agents or
sponges that could cause scratches.

Note: 

Do not use alcohol (spirit) on 

plastic parts, otherwise the surface may
become matt in appearance.

Caution: 

Ensure that the kitchen is ade-

quately ventilated. Avoid naked flames!

Clean the sliding switch with a soft,

damp cloth (mild detergent solution) only.
Do not use stainless steel polish on the 
sliding switch.

Stainless steel surfaces:

Use a mild non-abrasive stainless steel
cleaner.

Clean the surface in the same direction
as it has been ground and polished.

Do not use any of the following to clean

stainless steel surfaces: abrasive sponges,
cleaning agents containing sand, soda, acid
or chloride!

Aluminium and plastic surfaces:

Use a soft, non-linting window cloth or
micro-fibre cloth.

Do not use dry cloths.

Use a mild window cleaning agent.

Do not use aggressive, acidic or caustic
cleaners.

Do not use abrasive agents.

Summary of Contents for Cooker hood

















Reviews: