background image

TECNOEKA Srl ______________________________________________________________ use and instruction manual 

page 18 ________________________________________________________________________________________ 

11. Informations to the consumers 

 

Further  to  Directive  2012/19/UE,  the  symbol  of  the  crossed  rubbish  skip  on 
the appliance means that at the end of its life, the product must be disposed 
of separately from the other rubbish. The user must hand the appliance to a 
specialised waste collection centre for electric and electronic equipment. 

 

The separate collection of the rubbish and subsequent treatment, recovery and disposal help to 
produce  other  equipment  using  recycled  materials,  reducing  the  negative  effects  on  the 
environment  and  public  health,  which  would  be  caused  by  incorrect  management  of  the 
rubbish.  Should  the  user  dispose  of the  product abusively,  administrative  sanctions  would be 
applied. 

10.Established warranty

  

Tecnoeka’s products are exclusively designed for food use and are covered by warranty 
complying with Laws Regulation article n. 1490 and following) for professional users such as 
VAT holder customers  purchasing from Distributor.  
Tecnoeka’s products are professional and certified according to the IEC 60335-1 standards and 
can only be sold to professional users. 
With the exclusion of any additional warranty, the Seller will repair, at its sole discretion, only 
those parts of its products which prove vitiated by an original defect provided that, subject to 
revocation, the customer has reported the defect within 12 months from 'purchase and 
reported the defect within 8 (eight) days of the discovery, in writing enclosing a copy of the 
invoice, receipt or sales receipt proving the purchase. 
As well as in the event that the customer is not able to produce the invoice, receipt or sales 
receipt proving the purchase or are not respected the terms outlined above, the guarantee is 
expressly excluded in the following cases: 

1) Any failure or breakage of components caused by transport. 
2) Damage caused by inadequate electrical, plumbing and gas installation than provided in the 

installation manual, or by an abnormal function of the same. 

3) Damage resulting from incorrect installation of the product, or installation not in accordance 

with the requirements in the installation manual, and in particular damage due to failure of the 
chimneys and the discharges which this product is connected. 

4) Product use for purposes other than those it is intended for, as specified and resulting from the 

technical documentation released by Tecnoeka. 

5) Damage caused by use of the Product not in accordance with instructions contained in the user 

and maintenance manual. 

6) Product tampering. 
7) Adjustment Operations, maintenance and repair of the product performed by unqualified 

personnel. 

8) Use of non-original or not authorized parts by Tecnoeka. 
9) Damage or defect caused by negligent and / or reckless of the product, or in contrast with the 

instructions prescribed by the instruction and maintenance manual. 

10) Damage caused by a fire or other natural events and in any case any damage by accident or 

addicted to any cause not dependent on the manufacturer. 

11) Damage to parts subject to normal wear that need to be replaced periodically. 

Also excluded from the guarantee: the painted or enameled parts, knobs, handles, mobile or 
removable plastic parts, light bulbs, glass parts, seals, electronic parts, and all the possible 
accessories, transport costs from the based consumer, the end user and / or purchaser to the 
seat of Tecnoeka Ltd. and vice versa. The warranty doesn't include also the oven's replacement 
costs and the related installation costs. The warranty excludes products purchased as used or 
purchased from third parties not connected or authorized by Tecnoeka. 
 

Summary of Contents for EKC 96




















Reviews: