PAGE 6
User Manual
- Ecomatic 2010
User Manual
TECNORD
SERVOCOMANDI E REGOLAZIONE
ECOMATIC 2010 - User Manual 10-11_capitolo_A (generale) - tradotto1.1
Page 7
5 MIX-SALT 1 MODE
Once the MIX-SALT 1 automatic spreading mode has been selected, the display will visualize the page showed below
It displays the following operating parameters:
A
Material type selected for automatic spreading mode.
B
Vehicle speed in Km/h.
Connection to GPS step: 0km/h with dark text on blinking light background.
Speed automatically detected by GPS: dark text on light background (opposite of the picture above).
Manually set speed: light text on dark background (as in the picture above)
C
Tail position.
Detectable in systems provided with tail shift actuator with potentiometer.
D
Spreading width in meters.
Value settable with potentiometer #
13
between 1 and 12 meters.
E
Liquid percentage of the total amount of material, in %.
Value settable between 0 and 30% with the potentiometer #
11
.
Should the liquid be low, the percentage value is replaced by “- - -“ and the “Spread Alarm” #
19
will blink.
F
Material amount selected for spreading in g/m².
Value settable between 5 e 40 g/m² with the potentiometer #
10
.
Automatic spreading.
While being in one of the following operating modes:
MIX-SALT 1
MIX-SAND 1
MIX-SALT 2
MIX-SAND 2
SALT
SAND
push the pushbutton #
9
to start spreading. If no spreading mode is activated, push the pushbutton to activate it, and vice-
versa.
Automatic spreading is based upon the vehicle speed detected by the GPS device within the control box.
A
B
C
F
E
D
A
F
B
E
C
D
5.1
MIX-SALT 1 Mode
Once the MIX-SALT 1 automatic spreading
mode has been selected, the display will
visualize the page showed below. It displays
the following operating parameters:
A.
MATERIAL TYPE SELECTED
FOR AUTOMATIC SPREADING
MODE
B.
VEHICLE SPEED IN KM/H
Connection to GPS step: 0km/h with dark
text on blinking light background.
Speed automatically detected by GPS: dark
text on light background (opposite of the
picture above).
Manually set speed: light text on dark
background (as in the picture above).
C.
TAIL POSITION
Detectable in systems provided with tail shift
actuator with potentiometer.
D.
SPREADING WIDTH
IN METERS
Value settable with potentiometer #13
between 1 and 12 meters.
E.
LIQUID PERCENTAGE OF THE
TOTAL AMOUNT OF MATERIAL,
IN %.
Value settable between 0 and 30% with the
potentiometer #11.
Should the liquid be low, the percentage
value is replaced by “- - -“ and the “Spread
Alarm” #19 will blink.
F.
MATERIAL AMOUNT
SELECTED FOR SPREADING
IN g/m².
Value settable between 5 e 40 g/m² with the
potentiometer #10.
AUTOMATIC SPREADING
While being in one of the following operating
modes:
MIX-SALT 1
MIX-SAND 1
MIX-SALT 2
MIX-SAND 2
SALT
SAND
Push the pushbutton #9 to start spreading.
If no spreading mode is activated, push the
pushbutton to activate it, and vice-versa.
Automatic spreading is based upon the
vehicle speed detected by the GPS device
within the control box.
Spreading mode activation is indicated by the
“Spread On” warning light #18 lighting up.
- It blinks whenever the spreading mode is
active but not working, because the vehicle
stopped or the GPS signal is not yet detected.
- It lights up whenever the spreading mode
is active because vehicle is moving or it has
