ITALIANO
UPS EVO DSP MM RM
53
Manuale utente
12
Anomalie ed Interventi
Questo capitolo descrive le procedure che devono essere seguite in caso di funzionamento anomalo.
Nel caso in cui le azioni consigliate per risolvere l’anomalia non avessero esito positivo, contattare il Servizio
Assistenza. Fornire al Servizio Assistenza le seguenti informazioni:
Modello e numero di serie dell’UPS (stampati nell’etichetta sul retro del prodotto).
Descrizione del funzionamento anomalo e codice Fault visualizzato sul display grafico.
Allarmi ed anomalie che possono verificarsi durante il funzionamento dell’UPS sono descritti nella tabella
seguente. In caso di anomalia nel funzionamento: controllare la corretta connessione a TERRA-GROUND dell’UPS,
esaminare la posizione di tutti gli interruttori, leggere gli allarmi visualizzati sul display grafico e quindi consultare
la tabella sotto riportata.
Per ogni anomalia svolgere le azioni suggerite. Se il problema riscontrato non è descritto nella tabella o le azioni
consigliate non avessero esito positivo, contattare il Servizio Assistenza.
Rischio di shock elettrico. Non smontare l’UPS: contiene parti sotto tensione che sono
potenzialmente pericolose e possono provocare lesioni o morte per shock elettrico.
L’UPS non ha parti interne soggette a manutenzione da parte dell’utente. Interventi
tecnici di qualsiasi tipo devono essere compiuti solo da personale tecnico specializzato
ed autorizzato da TECNOWARE.
In caso contrario TECNOWARE declina ogni sua responsabilità.
Avviso per il personale tecnico autorizzato alla manutenzione: anche dopo aver spento
l’UPS e scollegato dalla rete elettrica, le parti interne sono ancora in tensione, essendo
collegate alle batterie, e quindi pericolose. Prima di effettuare qualsiasi tipo di
riparazione o manutenzione, portare l’interruttore Batterie dell’unità Box Batterie in
posizione “OFF” e poi scollegare il cavo Batterie.
ANOMALIA
POSSIBILE CAUSA
AZIONI PER RISOLVERE
Nessuna segnalazione sul pannello
frontale anche se è presente la
Tensione di Rete in Ingresso. Il
display grafico è spento.
Il cavo della linea d’Ingresso Rete
non è connesso correttamente.
L’interruttore Ingresso Rete è
“OFF”.
Controllare il cavo d’Ingresso
Rete e i collegamenti.
Controllare l’interruttore
d’Ingresso Rete: se è “OFF”
portare su “ON”.
Il simbolo
e il codice
d’allarme lampeggiano sul display
grafico e l’allarme acustico suona
ogni secondo.
La funzione EPO (Emergency Power
OFF) è attiva.
Chiudere il contatto di EPO per
disabilitare la funzione EPO.
I simboli
e
lampeggiano sul display grafico e
l’allarme acustico suona ogni
secondo.
Le batterie interne e/o esterne sono
collegate non correttamente.
Controllare i collegamenti delle
batterie interne e/o esterne.
Sul display grafico è visualizzato il
codice di Fault 28, è acceso il
simbolo
, e l’allarme
acustico suona continuamente.
La Tensione Batteria è troppo bassa
o il Carica Batteria è guasto.
Contattare il Servizio Assistenza.
Summary of Contents for EVO DSP MM 10.0
