TECSYSTEM T119 DIN Instruction Manual Download

Page: 6 / 14

T119DIN

TECHNICAL SPECIFICATIONS

T119DIN

POWER SUPPLY

Supply rated values

24 -240Vac-dc

50/60HZ

Maximum ratings 20-270 Vac-dc

●

Vdc with reversible polarities

●

INPUTS

3 series of PTC inputs

●

1 series for L1 (ALL1)

●

1 series for L2 (ALL2)

●

1 series for FAN

●

Connections to removable terminals

●

Input channels protected against electromagnetic interference

●

OUTPUTS

2 alarm relay (ALL1 / FAULT AND ALL2) SPDT

●

1 ventilation management relay (FAN) with timed latch (5-10-20-40 min.) delay OFF SPST

●

Output relays with 5A-250Vac-res COS

=1 contacts.

●

DIMENSIONS

106x90 mm DIN43880 depth58 mm (DIN track mounting)

TESTS AND PERFORMANCES

●

Construction in accordance with CE regulations

●

Protection from electrical interference EN 61000-4-4

●

Dielectric strength 1500 Vac for a min. between output relays and sensors, relays and power supply,
power supply and sensors

●

Ambient operating temperature from -20°C to + 60°C

●

Humidity 90% non-condensing

●

Self-extinguishing PPO UL94VO

●

Summary of Contents for T119 DIN















Search results

Summary of Contents for T119 DIN

Reviews:

Related manuals for T119 DIN

Brands by name

Popular brands

TECSYSTEM T119 DIN, Instruction Manual

Search results

Summary of Contents for T119 DIN

Reviews:

Related manuals for T119 DIN

Brands by name

Popular brands