background image

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Page 21

EMISSION CONTROL SYSTEM WARRANTY

Emission  Control  System  Warranty  (“ECS  Warranty”)  for  1995
and  later  model  year  California  small  off-road  engines  (for  other
states, 1997 and later model year engines):

A

.

APPLICABILITY

: This warranty shall apply to 1995 and later

model year California small off-road engines (for other states,
1997  and  later  model  year  engines).  The  ECS  Warranty
Period shall begin on the date the new engine or equipment is
delivered to its original, end-use purchaser, and shall continue
for 24 consecutive months thereafter.

B

.

GENERAL EMISSIONS WARRANTY COVERAGE:

Tecumseh Power Company warrants to the original, end-use
purchaser  of  the  new  engine  or  equipment  and  to  each
subsequent purchaser that each of its small off-road engines
is:

1.  Designed,  built  and  equipped  so  as  to  conform  with  all

applicable  regulations  adopted  by  the  Air  Resources
Board pursuant to its authority in Chapters 1 and 2, Part 5,
Division 26 of the Health and Safety Code, and 

2.  Free from defects in materials and workmanship which, at

any  time  during  the  ECS  Warranty  Period,  will  cause  a
warranted emissions-related part to fail to be identical in all
material  respects  to  the  part  as  described  in  the  engine
manufacturer’s application for certification.

C. THE  ECS  WARRANTY  ONLY  PERTAINS  TO  EMISSION-

RELATED PARTS ON YOUR ENGINE AS FOLLOWS:

1. Any  warranted,  emissions-related  parts  which  are  not

scheduled for replacement as required maintenance in the
Operator’s  Manual  shall  be  warranted  for  the  ECS
Warranty  Period.  If  any  such  part  fails  during  the  ECS
Warranty  Period,  it  shall  be  repaired  or  replaced  by
Tecumseh  Power  Company  according  to  Subsection  4
below. Any such part repaired or replaced under the ECS
Warranty shall be warranted for any remainder of the ECS
Warranty Period.

2.  Any warranted, emissions-related part which is scheduled

only  for  regular  inspection  as  specified  in  the  Operator’s
Manual shall be warranted for the ECS Warranty Period. A
statement  in  such  written  instructions  to  the  effect  of
“repair or replace as necessary”, shall not reduce the ECS
Warranty Period. Any such part repaired or replaced under
the ECS Warranty shall be warranted for the remainder of
the ECS Warranty Period.

3.  Any warranted, emissions-related part which is scheduled

for replacement as required maintenance in the Operator’s
Manual, shall  be warranted  for  the period  of  time  prior  to
the  first  scheduled  replacement  point  for  that  part.  If  the
part fails prior to the first scheduled replacement, the part
shall  be  repaired  or  replaced  by  Tecumseh  Power
Company  according  to  Subsection  4  below.  Any  such
emissions-related part repaired or replaced under the ECS
Warranty, shall be warranted for the remainder of the ECS
Warranty  Period  prior  to  the  first  scheduled  replacement
point for such emissions-related part.

4.  Repair  or  replacement  of  any  warranted,  emissions-

related  part  under  this  ECS  Warranty  shall  be  performed
at  no  charge  to  the  owner  at  a  Tecumseh  Authorized
Service Outlet.

5.  The owner shall not be charged for diagnostic labor which

leads to the determination that a part covered by the ECS
Warranty is in fact defective, provided that such diagnostic
work  is  performed  at  a  Tecumseh  Authorized  Service
Outlet.

6.  Tecumseh Power Company shall be liable for damages to

other 

original 

engine 

components 

or 

approved

modifications  proximately  caused  by  a  failure  under
warranty of an emission-related part covered by the ECS
Warranty.

7. Throughout  the  ECS  Warranty  Period,  Tecumseh  Power

Company  shall  maintain  a  supply  of  warranted  emission-
related  parts  sufficient  to  meet  the  expected  demand  for
such emission-related parts.

8.  Any Tecumseh Power Company authorized and approved

emission-related  replacement  part  may  be  used  in  the
performance of any ECS Warranty maintenance or repair
and  will  be  provided  without  charge  to  the  owner.  Such
use  shall  not  reduce  Tecumseh  Power  Company  ECS
Warranty obligations.

9.  Unapproved add-on or modified parts may not be used to

modify  or  repair  a  Tecumseh  Power  Company  engine.
Such use voids this ECS Warranty and shall be sufficient
grounds  for  disallowing  an  ECS  Warranty  claim.
Tecumseh Power Company shall not be liable hereunder
for  failures  of  any  warranted  parts  of  a  Tecumseh  Power
Company  engine  caused  by  the  use  of  such  an
unapproved add-on or modified part.

EMISSION-RELATED PARTS INCLUDE THE FOLLOWING:

1. Carburetor Assembly including internal components:

a) Carburetor gaskets
b) Intake pipe

2.  Air Cleaner Assembly including components:

a)  Air filter element

3. Ignition System including components:

a)  Spark plug
b) Ignition module
c) Flywheel assembly

4. Exhaust System including components:

a)  Catalytic muffler 

(if so equipped)

b)  Muffler gasket 

(if so equipped)

c) Exhaust manifold 

(if so equipped)

5. Crankcase Breather Assembly including components

a)  Breather connection tube

6. Evaporative Control System including components:

a)  Fuel line(s)

b) Fuel filter

c)  Canister 

(if so equipped)

d)  Fuel tank 

(if so equipped)

e)  Fuel fill cap 

(if so equipped)

Revised July, 2005

IMPORTANT!

The emission Regulations may be different for your country. The emissions Control Warranty Statement is only applicable 
to engines with an emissions compliance statement and decal that references “Emissions Regulations”.

Summary of Contents for LH358EA

























Reviews: