5
1.
Steam control button
2.
Iron temperature adjustment dial
3.
Iron thermostat light
4.
Easycord system (depending on model)
5.
Iron rest
6.
Illuminated on / off switch
7.
Power cord storage space
8.
Power cord
9.
Lock-System hoop (depending on model)
10.
Water tank filler cover
11.
Water tank
12.
Steam generator boiler (in the base unit)
13.
Iron-base steam cord
14.
Slide storage place for the steam cord
15. a
- Boiler rinse cap cover
b
- Boiler rinse cap
16.
Control panel
a
- Restart button
b
- “Water tank empty” light
c
- “Steam ready” light
d
- “Boiler rinse” light
e
- Steam output control dial
Description
Preparation
Due to the powerful steam output, a mesh type ironing board must be used to allow any excess steam to escape and to avoid
steam venting sideways.
What water may be used ?
• Your iron has been designed to operate using untreated tap water.
• Heat concentrates the elements contained in water during evaporation.
The types of water listed below contain organic waste or mineral elements
that can cause spitting, brown staining or premature wear of the
appliance: water from clothes dryers, scented or softened water, water
from refrigerators, batteries or air conditioners, pure distilled or
demineralised water or rain water should not be used in your iron.
Also do not use boiled, filtered or bottled water.
If your water is very hard (check with
your local water authority) it is possible
to mix untreated tap water with store-
bought distilled or demineralised water
in the following proportions: 50%
untreated tap water, 50% distilled or
demineralised water.
Filling the water tank
• Place your steam generator on a flat, stable, heat-resistant surface.
• Ensure that your steam generator is unplugged and that the soleplate and the iron rest
have cooled down.
• Open the water tank filler cover -
fig.4.
• Pour in untreated tap water up to the max mark -
fig.5.
• Close the water tank filler cover.
Using the Easycord system (according to model)
• Your iron is equipped with an extension cord system to prevent the cord from dragging
over the laundry and creasing it again when ironing.
• Take the steam cord out of its housing and unwind it completely.
• Remove the tie to release the cord outlet.
• Press the Eject button -
fig.6
and the Easycord system extends automatically.
• When the cord outlet tips, the Easycord system extends automatically without you
having to press the Eject button.
Locking system for retaining the iron on the base
- Lock-system (depending on model)
Your steam generator is equipped with a retaining clip which locks the iron on its base
for easier transport and storage -
fig.1
:
• Locking -
fig.2
• Unlocking -
fig.3
To carry your steam generator by the iron handle:
- Place the iron on the iron rest of the generator and raise the retaining hoop over the
iron until it locks into place (audible click) -
fig.2
- Grasp the handle of the iron to carry your steam generator -
fig.1
GB
D
F
NL
I
P
DK
S
FIN
N
GR
TR
PL
CZ
SK
SLO
RO
H
SR
HR
BG
RF
1800114819-centrale_vapeur_express.qxd:Mise en page 1 9/02/09 16:11 Page 5
Summary of Contents for Express GV7120E0
Page 2: ...1800114819 centrale_vapeur_express qxd Mise en page 1 9 02 09 16 11...
Page 63: ...62 1800114819 centrale_vapeur_express qxd Mise en page 1 9 02 09 16 12...
Page 127: ...126 3 7 2 8 Max 8 V 1800114819 centrale_vapeur_express qxd Mise en page 1 9 02 09 16 13...
Page 133: ...132 Note 1800114819 centrale_vapeur_express qxd Mise en page 1 9 02 09 16 13...
