118
119
ES
ES
118
119
EN
EN
PROBLEMS
CAUSES
SOLUTIONS
Leak through lid.
Volume of ingredients too high.
Reduce the quantity of ingredients
processed.
The lid is incorrectly positioned or locked.
Lock the lid correctly on the bowl.
The lid seal is not present.
Position the seal on the lid.
The seal is cut or damaged.
Change the seal, contact an approved
service centre.
Accessory error.
Check that you are using the recom-
mended accessory.
Leak through the bowl
spindle.
The bowl seal is not correctly positioned. Position the seal correctly.
The bowl seal is damaged.
Contact an approved service centre.
The locking ring
(D5)
is not locked correctly. Lock the ring correctly
(D5)
.
The blades do not rotate
easily.
Pieces of food that are too big or too
hard are blocking it from rotating.
Reduce the size or quantity of the
ingredients processed. Add some liquid.
Smell from motor.
On using the appliance for the first time, or
in the event of overload of the motor caused
by too large a quantity of ingredients or by
pieces that are too hard or too big.
Allow the motor to cool down (about
30 minutes) and reduce the number of
ingredients in the bowl.
“STOP” is displayed.
The appliance has detected too many
vibrations and has changed to the safety
mode.
Check that you are using the right speed
and that you are using the recommended
accessory.
“SECU” is displayed.
Motor overload caused by too many in-
gredients or pieces which are too hard or
too large or overuse without sufficient
cooling down time.
Allow the motor to cool down (about
30 minutes) and reduce the number of
ingredients in the bowl.
“SECU” is dis red
indicator light is flashing.
Overheating of temperature sensors.
Contact an approved service centre.
“Err1” is displayed.
+ red indicator light is
flashing.
The heating element is not working.
Check that the power pins under the bowl
are not clogged with food. If this is the
case, clean them and try again.
If that still does not work, contact an
approved service centre.
“Err2” is displayed.
Electronic fault.
Contact an approved service centre.
“Err3” is displayed.
Speed fault.
Contact an approved service centre.
“Err4” is displayed.
Communication fault with chopper
electronic card.
Contact an approved service centre.
Displays «Err8»
Default security sensor lock.
Contact an approved service centre.
“ntc1” is displayed.
+ red indicator light is
flashing.
Temperature sensor 1 is no longer
working.
Contact an approved service centre.
“ntc2” is displayed.
+ red indicator light is
flashing.
Temperature sensor 2 is no longer
working.
Contact an approved service centre.
WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK
PROBLEMS
CAUSES
SOLUTIONS
Problems when steam
cooking.
The steam regulator cap is not properly
attached.
Set the steam cap to ‘high steam’ (turn
towards you); this setting allows a
maximum amount of steam to build up in
the bowl for all types of steam cooking
(soups, etc.), so there will be more steam
in the bowl and the cooking process will
be more efficient.
The ‘low steam’ position allows a maximum
amount of heat and steam to be dispersed
into the bowl for all steam cooking
(soups, etc.). This position also helps to
avoid splashing during cooking.
The ‘high steam’ position allows a
maximum amount of condensation to
escape and results in dishes or sauces
with a better consistency (risotto, cream
desserts, sauces, etc.).
Insufficient cooking time
Cooking times are for information purposes only;
in most cases it ensures that the food is properly
cooked.
However, certain conditions may affect the
cooking time:
- size of the vegetables (cut or uncut)
- quantity of ingredients in the basket
- type of vegetables, their ripeness
- quantity of water in the bowl, which
corresponds to the measurement (0.7l).
If the food is not properly cooked, you can set an
additional cooking time.
You can also use the manual mode by selecting
a temperature of 130°C and the cooking
time according to the quantity and type of
ingredients.
The appliance does not
work.
It is not plugged in.
Plug the appliance into an electrical
socket.
The switch
(H)
is in position 0.
Move the switch to position 1.
The bowl or the lid are not correctly
positioned or locked.
Check that the bowl or the lid are correc-
tly positioned and locked according to the
diagrams in the instruction manual.
Excessive vibration.
The appliance is not positioned on a
flat surface, the appliance is not stable.
Place the appliance on a flat surface.
Volume of ingredients too high.
Reduce the quantity of ingredients pro-
cessed.
Accessory error.
Check that you are using the recom-
mended accessory.
Summary of Contents for FE90C160
