Teka DAL-90, Instruction Manual

1

150/ 120 mm reduction.

1

Support for tubecover.

4

Wall plugs (Ø8 x 40).

4

Long bolts (Ø5 x 45).

2

Wall plugs (Ø6 x 30).

2

Long bolts (Ø4 x 30).

2

Ø6,4 x Ø18, washers.

2

Screws (Ø3,9 x 13).

2

Clips.

Fig. 1 (Page 31)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
10 are complied with.
To obtain optimum performance, the external
conduct must not be more than FOUR
METRES long, have no more than two 90°
angles and its diameter must be at least Ø120.

1) Trace and drill the points for fitting the wall plugs
onto the wall (A1) (Ø8 x 40). See figure nr. 1.
2) Fit the wall plugs (A1) and screw in the long bolts
(A2) (Ø5 x 45) leaving them protruding 5 mm out of
the wall.
3) Attach the kitchen hood to the long bolts (A2).
Straighten the apparatus and tighten the long bolts.
4) Remove the metal filters. Loosen the screws
(without unscrewing them) of the EASYCLEAN
panels (A19), move the panels aside carefully and
take them off.
5) Trace the location of the wall plugs (R) (Ø8 x 40),
through the inside of the kitchen hood.
6) Loosen the long bolts (A2) and take the kitchen
hood off.
7) Drill into the wall and fit the wall plugs (R) (Ø8 x
40).
8) Fit the part (B) if the inner tube (not supplied) is
Ø120.
9) Attach the inner tube with a clamp (not supplied)
to (B) or on to the motor's air outlet vent as the case
may be.
10) Attach the kitchen hood, tighten the long bolts
(A2) and (S) (Ø5 x 45) with the washers (T) (Ø6,4 x
Ø18).
11) Mount the EASYCLEAN panels again (A19). Fit
the metal filters.
12) Lift the upper tubecover up to the desired height
and mark its shape on the wall. 
13) Fit the clips (F) to the support (C). 
14) Centre the support (C) around the shape
marked; trace and drill the fixing points for the wall
plugs (E) (Ø6 x 30). Attach the support (C) with the

long bolts (D) (Ø4 x 30).
15) Connect the upper part of the inner tube (not
supplied) to the exit. 
16) Attach the upper tubecover with the screws (G)
(Ø3,9 x 13).

When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life of
between three to six  months, depending on
the individual  conditions of use. These filters
cannot be washed nor regenerated. They must
be replaced once their useful life comes to an
end.

Fig.  1 (Page 31)

1) Trace and drill the points for fitting the wall plugs
onto the wall (A1) (Ø8 x 40). See figure nr. 1.
2) Fit the wall plugs (A1) and screw in the long bolts
(A2) (Ø5 x 45) leaving them protruding 5 mm out of
the wall.
3) Attach the kitchen hood to the long bolts (A2).
Straighten the apparatus and tighten the long bolts.
4) Remove the metal filters. Loosen the screws
(without unscrewing them) of the EASYCLEAN
panels (A19), move the panels aside carefully and
take them off.
5) Trace the location of the wall plugs (R) (Ø8 x 40),
through the inside of the kitchen hood.
6) Loosen the long bolts (A2) and take the kitchen
hood off.
7) Drill into the wall and fit the wall plugs (R) (Ø8 x
40).
8) Fit the diffuser (A5) on to the motor's air outlet
vent. 
9) Attach the kitchen hood, tighten the long bolts (A2)
and (S) (Ø5 x 45) with the washers (T) (Ø6,4 x Ø18).
10) Put the filters into the lateral draught section of
the motor making the holes in the filters match up (A)
with the pivots (B) of the motor carcass. Turn as
indicated in the diagram.
11) Mount the EASYCLEAN panels again (A19). Fit
the metal filters.
12) Lift the upper tubecover up to the desired height
and mark its shape on the wall. 
13) Fit the clips (F) to the support (C). 
14) Centre the support (C) around the shape
marked; trace and drill the fixing points for the wall
plugs (E) (Ø6 x 30). Attach the support (C) with the
long bolts (D) (Ø4 x 30).
15) Attach the upper tubecover with the screws (G)
(Ø3,9 x 13).

Active charcoal filters  (Optional)

Installation

Accesories supplied

13

ENG