background image

WARNING

Please use your furniture correctly and safely. Improper use can cause safety hazards, 

or damage to your furniture or household items

Carefully read the following safety information.

Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys 

placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.

NEVER

 allow children to climb or play with the TV or furnishing supporting the TV.

NEVER

 place toys, food, remote, etc. on top of the TV or TV furnishing.

ALWAYS

 use either the safety hardware as instructed or other wall anchoring device.

Relocating audio and/or video equipment to furniture not specifi cally designed to support audio and/or video equipment 

may result in death or serious injury due to furniture collapse or over turning onto a child.

NEVER

 place a TV on furniture that is not intended to support a TV.

NEVER

 exceed the maximum size and weight of the TV shown in the instructions.

Be sure to apply the TV warning label as shown in the instructions.

Overloading drawers and shelves may result in furniture that can break or sag, or tip-over which may result in injury. 

NEVER

 exceed the weight limits shown in the instructions. 

Place the heavier items on lower shelves as far back from the front as possible.

Load the bottom surfaces fi rst to avoid top-heavy furniture.

Moving furniture that is not designed to be moved or equipped with casters may result in injury or damage to furnishings or 

personal property.

ALWAYS

 unload shelves and drawers, starting with the top surfaces, before moving.

NEVER

 push or pull furniture on carpet. Have a friend help lift properly to move and/or reposition it.

Summary of Contents for Hythe 5426437






















Reviews: