Tekno RC EB48.2 Manual Download

Page: 28 / 32

TKR5220

TKR1525

TKR1221

TKR5065

TKR1525

TKR5067

TKR1221

You need a separate servo for the brakes.

A servo with at least 160oz/in torque @ .15sec

or faster is recommended.

Radio Setup:

Adjusting the Brakes and Brake Bias:

The total braking force is set by

your transmitter via servo travel

(EPA for 3rd/AUX/Brake channel)

When your servo is in the

neutral position, there should be

no contact with the brakes. Use

the ESC settings to adjust drag brake.

Adjust the brake linkage stops (TKR5222)

and servo EPA to set the brakes to your liking.

Some prefer the brakes to come on very quick,

while others prefer them to be a little more progressive.

The brakes bias is adjusted by lengthening or shortening the brake

adjustment turnbuckle (TKR5057). A longer link will provide more

rear braking bias, a shorter link will provide more front braking bias.

We recommend leaving the servo horn loose while adjusting the

brake bias. This way you can test the brake bias, take the servo horn

off to adjust, test, repeat if necessary. When you have the brake bias

where you want it, tighten down the servo horn.

To set up the brake servo action, you will need

a radio transmitter that has the ability to perform

3rd/AUX mixing on the throttle channel.

Adjust the mixing function so the brake servo

only moves when activating the brakes (moving

the trigger forward on your transmitter). If the

servo is also moving when on throttle, you will

damage the brake system or your servo and the

car will not function properly.

Set the ESC brakes to 0 (zero). Although,

you can still use the ESC for partial brakes or

drag brake if desired.

Refer to your transmitter manual for mixing

functions specific to your brand.

TKR1601

TKR5222

TKR5058

TKR1201

TKR1525

TKR5056

TKR1327

TKR1601

TKR5222

Thread

Lock

Bag R

Mechanical Brakes

(optional - TKR5206X)

Step

R-5

Step

R-6

Step

R-7

Step

R-8

TKR1327

M3x16mm Flat Head Screw

TKR5058

Pivot Ball M3x5.8mm
No Flange

TKR1601

M3x4mm Set Screw

TKR1201

M3 Locknut Black

TKR1525

M3x14mm Cap Head Screw

Summary of Contents for EB48.2

































Search results

Summary of Contents for EB48.2

Reviews:

Related manuals for EB48.2

Brands by name

Popular brands

Tekno RC EB48.2, Manual

Search results

Summary of Contents for EB48.2

Reviews:

Related manuals for EB48.2

Brands by name

Popular brands