background image

8 • IL573 Tek-ENTRY

®

 Telephone Entry System Phone-Line Version Manual

Copyright © TekTone Sound & Signal Mfg., Inc. All Rights Reserved.

System Installation and Programming

1. When the programming menu displays “ROTARY PHONES?,” press the # key. The

message “ENABLE/DISABLE” will appear.

2. Enter “00” to enable rotary phone use; or enter “11” to disable rotary phone use. Press

the “#” key to save.

3. Press the “*” key to return to the programming menu.
4. If desired, press the “*” key to end program mode.

Guard Telephone Number

This is the telephone number that all calls will be routed to when night service is enabled.
See 

Night Service 

in the 

System Introduction—Special Features 

section for more

information

.

1. When the programming menu displays “GUARD PHONE,” press the “#” key. The

message “GUARD PHONE NO.” will appear.

2. Enter a telephone number and press the “#” key to save.
3. Press the “*” key to return to the programming menu.
4. If desired, press the “*” key to end program mode.

Erase/Reset to Factory Default

This function erases all programming, including Tenant Dial Codes and Keyless Entry
Codes, and returns the system to factory defaults.

1. When the programming menu displays “ERASE/RESET TO FACTORY DEFAULT,”

press the “#” key. The message “ARE YOU SURE? *=NO #=YES” will appear.

2. Enter “*” to retain system programming; or enter “#” to erase all programming and

return to factory defaults.

3. Press the “*” key to return to the programming menu.
4. If desired, press the “*” key to end program mode.

Adjustments

Volume Control

The communication volume levels are factory preset for normal operations. The levels can
be increased or decreased by adjusting the potentiometers located along the bottom of the
system controller, behind the front display plate. Audio level from the entry system to the
suite is controlled by the 

MICROPHONE

 

VOLUME

 

control. Audio level from the suite to the entry

system is controlled by the 

SPEAKER

 

VOLUME

 control.

Rotary Phone Pulse Sensitivity

Telephone companies do not specify or guarantee the waveshape of the signal transmitted
when the tenant dials the digit “9” from a  rotary (pulse) telephone. In order to achieve best
results, Tek-ENTRY

®

 Telephone Entry Systems are furnished with a sensitivity adjustment

potentiometer, as well as an indicator lamp to view the incoming rotary signal (pulses). This
potentiometer is labeled 

PULSE

 

SENSITIVITY

 on the system controller. The pulse sensitivity is

factory preset so that a wide range of incoming rotary signals will properly trigger the door
circuit, and so will usually not require adjustment. If adjustment is necessary because the
door strike cannot be properly triggered, use the following procedure.

1. Set the 

PULSE

 

SENSITIVITY

 control to the middle position.

2. From the entry system, call the suite telephone that is not triggering the door circuit.

3. Observe the 

PULSE

 

INDICATOR

 while the digit “9” is being dialed from the suite

telephone. The indicator should flash distinctly every time a pulse is heard.

4. If the indicator barely comes on, the sensitivity is set too low. Increase the sensitivity

by turning the shaft of the potentiometer clockwise 1/8th of a turn at a time until the
indicator shows distinct flashing.

Summary of Contents for Tek-ENTRY TE903A

























Reviews: