DM
5010
Instrument
Interfacing
Guide
Table
2
(cont)
Header
Argument
Description
OVER
OFF
Disables
overrange SRQ
(OVER ON).
If overranged
when talked, returns
‘
1.E+99;'
and does not gen
erate
an SRQ.
OVER
ON
Enables
overrange SRQ. If
overranged
when talked,
re
turns
“
1.E+99;" and gener
ates an SRQ.
OVER?
Returns
‘OVER ON;' or
“OVER OFF;’
.
RATIO
(RAT)
<num>,
<num>
Sets values for
offset
and
scale
used
in CALC RATIO
command. First argument
is
for
scale, second for offset.
RATIO?
(RAT?)
Returns
“RATIO
<num>,
<num>;
“
.
RDY?
Returns
“RDY
0;
’ if a mea
surement is in progress or if
the
instrument is waiting for a
trigger. Returns “RDY 1;
’ if a
measurement is available.
Also
see
OPC ON.
RQS
ON
Enables instrument
to gener
ate service requests.
RQS
OFF
Disables
all
SRQ’s.
Instru
ment responds to ERR?
with
out
first
being
serial polled.
RQS?
Returns
“RQS OFF;
’ or
“
RQS ON;
’.
SEND
(SEN)
Returns
latest measurement.
If no measurement is avail
able,
the instrument triggers a
measurement
and
then out
puts
it. If CALC CM
PR is en
abled,
returns
1, 2, or 3 to
indicate
relationship of
mea
surement to
LIMITS. See
CALC
CMPR.
SET?
Returns all
instrument
settings that may be queried.
See Power
On Settings.
SOURCE
(SOUR)
FRONT
Connects
front panel connec
tor
inputs.
Table
2
(cont)
Header
Argument
Description
SOURCE
(SOUR)
REAR
Connects
rear
interface con
nector inputs.
SOURCE?
(SOUR?)
Returns
‘SOURCE FRONT;’
or
“SOURCE REAR;'.
TEST
Returns
0 if calculation
checksum is
correct; 351
if
erroneous.
USER
ON
Enables INST ID
button ser
vice
request.
USER
OFF
Disables INST ID button ser
vice
request.
USER?
Returns
“USER
ON;"
or
‘
USER OFF;'.
Sending Messages to the DM 5010
Most
GPIB controllers provide a high-level state
ment
that allows you to transfer device-dependent
messages to
the DM 5010.
In the 4050-Series and the
4041, it’
s the PRINT
statement.
4050-Series:
170
616:
"ACVJLFR ON"
4041:
170
tt
16:"ACV;LFR 0MH
A useful variation assigns the DM 5010 address to
a variable and inserts that variable
in the PRINT state
ment in place of
the number for the address. This
works with either the 4050-Series or
4041 and allows
you
to change
the
program to work with the DM 5010
set
to other addresses by changing only the state
ment
that assigns the variable.
4050:
200
D-16
210 PRINT fcDt"ACViLFR
ON"
4041:
200
Dee-16
210
"ACVJLFR
ON”
5
Summary of Contents for DM 5010
