Bedienungsanleitung -
DM 5010
VORSICHT
Um
Beschädigung
des
Gerätes zu
vermeiden, darf
zwischen
den Stiften 28B (Hi)
und 28A (Lo) am
rückseitigen Interface-Anschiuß P1031 auf der ADC
Platine
(A17) keine Spannung
angelegt
werden,
die
42,4
Vs AC oder 60
VDC übersteigt.
Schalten
Sie nicht zwischen der
Frontplatte
und dem
rückseitigen Interface-Anschiuß um, während an
den Eingangsanschlüssen auf der Frontplatte eine
Spannung
von
über 500 V$ angelegt ist. Betriebs
fehler
und eine Beschädigung des Gerätes können
die
Folge sein.
Gleichspannungs-
(DC)
Messungen
Wenn die
Taste
DCV gedrückt ist, mißt das DM 5010
Gleichspannungen in
den Bereichen: 200 mV, 2 V, 20
V,
200
V
und 1000 V, Die Darstellung zeigt ein positives
Zeichen
an wenn der Eingang am HIGH Anschluß mit
Bezug
auf
den LOW Anschluß
positiv
ist. Beachten Sie
die Maximalwerte
für
die Eingangsspannung.
Widerstandsmessungen
Drücken
der
Taste OHMS gibt das DM 5010 frei für die
Messung
von Widerständen in den Bereichen: 200 Ω,
2
kΩ, 20 kΩ, 200 kΩ, 2 MΩ und 20 MΩ. Der normale
Stromfluß
geht
vom Anschluß HIGH zum Anschluß LOW.
Tabelle
2-3 enthält die Strom- und maximalen Span
nungswerte
an den Eingangsanschlüssen (innerhalb
der
Bereiche).
Die maximale
Spannung
am Anschluß
HIGH bezogen auf Anschluß
LOW
liegt unter 5
V,
Tabelle
2-3
Funktion
OHMS
Bereich
Typischer Strom
V
max.
200 Ω
2
kΩ
20 kΩ
200 kΩ
2MΩ
1,02
mA
bis 1 mA
0,12
mA
bis
0,1
mA
9,2 µA
bis 10 µA
1,08
µA
bis 1 µA
0,12
µA
bis 0,1
µA
0,2
V
20 MΩ
0,12
µA
bis 0,04 µA
0,8
V
Messung von Dioden
Wird die Taste DIODE TEST gedrückt, erzeugt das
DM
5010
am Anschluß
HIGH einen Gleichstrom von
1
mA. Zur Messung des Spannungsabfalls wird die Diode
mit
der Anode
an HIGH
und der Kathode an LOW ange
schlossen. Es können Geräte mit einem Spannungsab
fall
unter 1,999 V geprüft werden.
Das sind die
meisten
Dioden
und einige LED’
s.
Zur
Prüfung des umgekehrten Spannungsabfalls
vertauschen
Sie
die
Anschlüsse der Diode
am Gerät.
Die
Darstellung
sollte
OC
anzeigen.
Meßgeschwindigkeiten
Das
DM 5010 arbeitet mit einer von zwei Meßge
schwindigkeiten.
Bei der Geschwindigkeit FAST (Taste
CONVERSION RATE
erleuchtet) führt es Messungen mit
der maximalen, für
die gewählte Funktion spezifizierten,
Geschwindigkeit
durch. Die Meßergebnisse
werden
3
1/2-stellig
angezeigt. Ist
die Taste nicht erleuchtet
erfolgen
die
Messungen mit der normalen für die
gewählte
Funktion spezifizierten Geschwindigkeit und
die
Ergebnisse werden
41/2-stellig angezeigt.
Triggerung
Das
DM
5010 verfügt
von der Frontplatte aus über zwei
Triggerbetriebsarten
RUN und
TRIGGERED. Wenn die
Taste RUN gedrückt
ist erfolgen die
Messungen frei
laufend
mit der gewählten Meßgeschwindigkeit. Bei
jedem
Drücken
der
Taste
TRIGGERED wird eine
Messung ausgelöst.
Ferner
können Messungen über den rückseitigen
Interface-Anschiuß,
Stifte 16A
und 16B
(Lo) am Isolation
Board
(A15)
getriggert werden. Dazu muß eine interne
Überbrückung
installiert werden. Hinweise dazu findet
qualifiziertes
Servicepersonal im Abschnitt „Wartung“.
Durch
Einbau
dieser Brücke
wird die
Triggerfunktion
EXTRIG
freigegeben.
Zur Anwendung der EXTRIG Trig
gerung drücken Sie die
Taste TRIGGER und sperren
damit die frei laufende Triggerung
des Gerätes. Für die
Auslösung
der
internen
Triggerung wird bei EXTRIG ein
negatives, TTL kompatibles Signal benötigt. Für eine
einzelne
Triggerung
muß diese Leitung zwischen 0,5
und
10 µs gehalten werden. Wird
sie längere Zeit niedrig
gehalten, triggert
das Gerät Mehrfachmessungen.
ADD JUL
1986
German 2-9
Summary of Contents for DM 5010
