background image

Telecast

Operating Details

 9

Operating Details

Battery Charging

Charge the internal UPS batteries at a minimum 13.8 VDC for 16 hours (40 mA trickle charge) by 
attaching each unit to its external power supply. This will permit battery operation for up to 
20 minutes during line power losses.

Indicators

The three LEDs on the front panel are shown in Figure 11.

Figure 11. Front Panel

¥

EXTERNAL

 

POWER

.

 

When this green LED is illuminated, an external supply of between 12 and 

24 VDC is connected.

¥

INTERNAL

 

RESERVE

.

 This LED is illuminated green when the power is on and the internal 

battery is adequately charged. This LED lights after one half hour of charge. There may be a 
few minutes of reserve after the indicators extinguish. This LED is illuminated red when the 
internal battery is discharging.

¥

LINK

 

STATUS

.

 

This red LED is on when the Þber optic link is 

not

 properly attached, or the 

system units are 

not 

communicating properly. This indicator is meaningful only if one of the 

other two LEDs is on.

¥

AUDIBLE

 

ALARM

.

 An audible alarm has been incorporated into the Adder 882 in addition to the 

LED indicators on the front panel. This alarm alerts the user that the internal batteries are 
discharging. A defeat switch for the audible alarm is located inside the unit on the main circuit 
board.

Powering Up

Note: 

A locking switch is provided to prevent inadvertent power turn off. Never try to move the 

front panel switch without Þrst pulling on the switch lever to disengage its lock.

With power OFF at both units, check all electrical and optical connections as described in 

Installation 

on page 3. Firmly seat and latch all connectors. To operate the power switch:

1. Pull the lever away from the panel.

2. Move it 

up

 for power ON, or 

down

 for power OFF. 

The power switches at both units must be on for the system to achieve normal function.

3. Switch on the power to both Adder 882 units.

Verify that the green 

EXTERNAL

 

POWER

 

LEDs

 

are illuminated, and that the red 

LINK

 

STATUS

 

LEDs do not light. If you do not get this result, refer to the Troubleshooting Chart on page 16.

POWER

ADDER     882

ä

AUDIO/DATA MUX/DEMUX

Fiber Systems, Inc.

Te l e c a s t

INTERNAL 
RESERVE

   LINK STATUS

         EXTERNAL 
           POWER

ON

OFF

Summary of Contents for Adder 882



























Reviews: