Date
Code Number:
Series
Model number
Draft
TELECO AUTOMATION SRL -
Viale del Lavoro, 5 - 31014 Colle Umberto (TV) ITALY
TELEPHONE:
++39.0438.388511 FAX: ++39.0438.388536
This document is the property of Teleco Automation Srl who reserves all reproduction and copying rights
T304.01
26-05-08
TVPRHxxx-S
SOFT TOUCH RADIO CONTROL TVPRH
ATTENTION !
The appliance must be installed only by qualified technical personnel in
compliance with the standards in force. All connections must be rated
for a 230V single-phase power supply. To disconnect the appliance from
the mains use an all-pole switch with a minimum distance of 3.5 mm
between the contacts. All wiring used must guarantee sufficient
insulation as required by electrical safety standards in force.
The programmer only carries out remote and manual movement
commands. All the necessary safety devices required by the installation
are to be organised separately. The programmer is in conformity with
the RAEE and RoHS directives and it is intended for indoor use only
(IPX0). The appliance is not to be used by children.
Children should be watched to make sure they do not play with the
appliance.
The radio frequency reception of the appliance may be disturbed by
several factors as follows:
-radio electric interferences from other appliances in the same room
that are transmitting on the same frequency
-if the appliance is housed in a metal casing; only plastic casing should
be used.
1- GENERAL DESCRIPTION
Electronics for the remote control of tubular motors for rolling shutters
with mechanical or electronic travel limits incorporated in the motor.
Possibility to control the device manually or via radio (in the 868
version). The work time is fixed at 60 seconds.
Programming is either carried out on the receiver or remotely via
transmitters.
This appliance may be commanded by the standard transmitters of the
series TVLink.
The standard transmitters may be memorized or cancelled in the
receiver using the command buttons.
The maximum number of codes that can be memorized is 42 .
1.1 Operating way
It is possible to select different ways of functioning. The operating way
involves both the commands from push-buttons and the commands via
radio. These phases are possible only for the first 10 seconds after the
switching on of the device.
1.1.1 Automatic opening and closing movement
1) Power up the device, the Led1 will light up for two seconds.
2) After the two seconds, push 8 times the stop push-button and hold it
pushed for two seconds.
The Led will light up every time the stop push-button will be pressed.
1.1.2 Automatic opening movement and “present man” closing
movement
1) Power up the device, the Led1 will light up for two seconds.
2) After the two seconds, push 9 times the stop push-button and hold it
pushed for two seconds.
The Led will light up every time the stop push-button will be pressed.
1.1.3 “Present man” opening and closing movement
1) Power up the device, the Led1 will light up for two seconds.
2) After the two seconds, push 10 times the stop push-button and hold it
pushed for two seconds.
The Led will light up every time the stop push-button will be pressed.
2- Transmitters
Use transmitters with at least 2 channels.
The transmitters are pre-coded by the manufacturer and each
transmitter has its own unique code.
Attention: if you press and hold down a transmitter button for more
than 30 seconds, the transmitter with switch off automatically.
The receiver is compatible with all transmitters of the TVlink system:
TVTXV, TVTXP, TVTXC, TVTXK, TVTXQ, TVTXL.
3
Transmitter channel functions
CH1 – Open/Stop
CH2 – Close/Stop
CH3 – Open/Stop
CH4 – Close/Stop
CH5 – Open
CH6 – Stop
CH7 – Close
Warning! For the first 4 channels the channel opposite to the current
operation always carries out a stop.
2.1 - Memorizing via a transmitter (first installation, empty
memory)
1) Press button P3 on the transmitter, the receiver led will light up and
remain lit.
2) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash, release the button.
To insert another pair of channels via radio follow the procedure in
paragraph 2.2.
2.2 - Memorizing via a transmitter (ulterior transmitters)
(memory addressing procedure)
1) Press button P3 on the already memorized transmitter, the receiver
led will light up and remain lit.
2) Within 5 seconds press a channel that is already memorized in the
receiver, the led will switch off for 1 second and then light up again for
5 seconds.
3) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash intermittently, release the button.
To memorize more transmitters repeat points 1-2-3.
2.3- To cancel a code via radio
1) Press button P3 on the transmitter for three times within five
seconds, the receiver led will flash slowly.
2) Transmit one of the two channels of the pair to be cancelled, once
cancelled, the led will switch off.
3- Memorization, cancelling from the receiver.
These functions may only be carried out during the first 10 seconds after
having powered up the device.
Within these ten seconds you may only carry out one single operation;
Memorizing or cancelling a single channel or cancelling the entire
memory content.
3.1- To memorize a channel
1) Power up the device, LED1 will light up for two seconds.
2) After two seconds press and hold down the stop button, LED1 will
light up.
3) Transmit the channel to be memorized. The LED will flash to
confirm memorization.
The channels are memorized in pairs, ch1 with ch2, ch3 with ch4, ch5
with ch6 and ch7.
3.2- To cancel a single code
1) Power up the device, LED1 will light up for two seconds.
2) After two seconds press the stop button twice and hold it down, LED1
will light up and flash slowly.
3) Transmit the channel to be cancelled. The LED will turn off to
confirm cancellation.
3.3 – To cancel the entire memory content
1) Power up the device, LED1 will light up for two seconds.
2) After two seconds press the stop button three times and hold it down
for ten seconds, LED1 will light up and flash quickly, when cancellation
has been carried out it remains lit, release the button.
4- If the memory is full
If the memory is full the led will flash three times when the device
is powered up.
TVLink RS868
