background image

 

10

 

 

 

 

 

 

 

 

           CELL ROUTE-GSM 

 

 

              

Technical Specification 

 
 

 
 
 
 
 

 
 
 
 
 

 

 

 

 
 
 
 

 
 
 
 
 

 

 

 

 
 
 
 
 

 

 

Telephony Interface 

 
Call Control 

 

 

DTMF 

 

Line Voltage 

 

 

48v on hook 

Loop Current 

 

 

40mA off hook 

Line impedance   

 

600-ohm complex 

Ring Voltage 

 

 

70Vrms 

Ring Load 

 

 

REN 4 

CLIP 

   Bellcore 

FSK 

 

 

    

 

 GSM Interface 

 

Bands  

E-GSM 

900MHz 

  GSM 

1800MHz 

    

             GSM Phase 2+ 

 
Transmit Power  Class 4 (2W) for E-GSM 900 MHz Class 1 (1W) 

for GSM 1800MHz 

 
Speech Codecs  Half Rate (ETS 06.20) 
 

Full Rate (ETS 06.10) 

  

 

Enhanced Full Rate(ETS 06.50 / 

 

06.60 / 06.80) 

 
Data Rate 

2400,4800,9600,Baud 

 
SIM Card 

3V 

 
Antenna 

Integral Omni directional Antenna 

 

With MCX connector for external 

 Antenna 

option 

 

 

Physical Interfaces 

 
Telephone 

Analogue / RJ11 

 

 
Data Port 

RS232 / RJ45 with optional DB-9 

  Converter 
 
GSM Antenna 

An SMA male connector 

 
SIM Card 

3V Small card retained under rear panel 

 
Indication 

2 x LED indication for battery / Transmission 
Status 

 

Approvals 

 
  CE Certification to R & TTE directive 1999/S/SEC 
 
  GSM Certifications: 
 

 ETS 300 607-1 Digital Cellular Telecommunications Systems 

 

 EN  301 419-1 Global System for Mobile Communications 

 

 ETS 300 342-1 Radio Equipment and Systems 

 

     

    Features Overview 

 

High Ringer Equivalence POTS Interface 
Supports up to 4 additional extensions 
 
Highly compatible POTS user interface 
 
Integral Battery Back-up 
 
Caller Line ID Presentation (Bellcore) 
 
Additional GSM network features may be available  
Subject to network availability and support 
 
RS232 Data Port for emails/web and transmission / 
reception of PC faxes (using WinFax Pro) 
 
SIM lock for asset protection 
(For details contact your service provider) 
 
Network Lock for asset protection 
(For details contact your service provider) 
 
Remote Software Upgrades 
 
Remote Antenna facility 
 
Off-hook Howler 
 
Gain adjustment on microphone 1>5 
 
Gain adjustment on speaker 1>5 
 

 

               Power Supplies 

 
Primary         110-240Vac @ 47-63Hz 
 
Secondary      2xA size NiMH rechargeable batteries      

        with Auto switch over to mains failure 

 
Performance   11 hours standby time (subject to     

         Humidity and temperature) 
 
        Up to 2 hours Talk time (subject to 
        Humidity and temperature)  

 

 

Physical Specifications 

 
Height  

 

150mm 

 
Width  

 

122mm 

 
Depth 

  42mm 

  

 
Weight  

 

460gm  

 
Operational Temperature Range     0C to 45C 

 

Summary of Contents for CELLROUTE-GSM











Reviews: