TELEDYNE API T300 Operation Manual Download

Page: 151 / 347

Teledyne API – Model T300/T300M CO Analyzer

Communications Setup and Operation

149

6.7.2.3.

SELECTING A HESSEN PROTOCOL TYPE

Currently there are two versions of Hessen Protocol in use. The original
implementation, referred to as

TYPE 1

, and a more recently released version,

TYPE 2

that has more flexibility when operating with instruments that can measure more than
one type of gas.

For more specific information about the difference between

TYPE 1

and

TYPE 2

download the

Manual Addendum for Hessen Protocol

from the Teledyne API web site:

http://www.teledyne-api.com/manuals/

To select a Hessen Protocol Type press:

SAMPLE

RANGE=50.0 PPM CO= XX.XX

<TST

TST> CAL

SETUP

SETUP X.X

COMMUNICATIONS MENU

HESN

COM1 COM2

EXIT

SETUP X.X

HESSEN VARIATION:TYPE1

<SET

SET>

EDIT

EXIT

SETUP X.X

HESSEN VARIATION:TYPE1

TYP1

TYP2

ENTR

EXIT

discards the new

setting.

ENTR

accepts the

new setting.

Use these

buttons to

choose the

Hessen type.

SETUP X.X

PRIMARY SETUP MENU

CFG DAS RNGE PASS CLK

MORE

EXIT

SETUP X.X

SECONDARY SETUP MENU

COMM

VARS

DIAG

EXIT

Note

While Hessen Protocol Mode can be activated independently for RS-232
and COM2, the TYPE selection affects both Ports.

06864D DCN7562

Summary of Contents for T300




























































































































































































































































































































































Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands

TELEDYNE API T300, Operation Manual

Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands