TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 153 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Communications Setup and Operation

151

6.7.3.

HESSEN PROTOCOL GAS LIST ENTRIES

6.7.3.1.

HESSEN PROTOCOL GAS ID

The T300/T300M Analyzer keeps a list of available gas types. Each entry in this list
takes the following format:

[GAS TYPE],[RANGE],[GAS ID],[REPORTED]

WHERE:

GAS TYPE

= The type of gas to be reported (e.g. CO, CO

2

, O

2

, etc.).

RANGE

= The concentration range for this entry in the gas list. This

feature permits the user to select which concentration range
will be used for this gas list entry. The T300/T300M Analyzer
has two ranges:

RANGE1

or LOW &

RANGE2

or HIGH (See

Section 5.4.1).

0 - The HESSEN protocol to use whatever range is currently

active.

1 - The HESSEN protocol will always use

RANGE1

for this

gas list entry.

2 - The HESSEN protocol will always use

RANGE2

for this

gas list entry.

3 - Not applicable to the T300/T300M Analyzer.

GAS ID

= An identification number assigned to a specific gas. In the

case of the T300/T300M Analyzer in its base configuration,
there is only one gas CO, and its default GAS ID is 310. This
ID number should not be modified.

REPORT

= States whether this list entry is to be reported or not reported

when ever this gas type or instrument is polled by the
HESSEN network. If the list entry is not to be reported this
field will be blank.

While the T300/T300M Analyzer is a single gas instrument that measures CO, it can
have additional, optional sensors for CO

2

or O

2

installed. The default gas list entries for

these three gases are:

CO, 0, 310, REPORTED
CO

2

, 0, 311, REPORTED

O

2

, 0, 312, REPORTED

These default settings cause the instrument to report the concentration value of the
currently active range. If you wish to have just concentration value stored for a specific
range, this list entry should be edited or additional entries should be added to the list.

EXAMPLE: Changing the above CO gas list entry to read:

CO, 2, 310, REPORTED

would cause only the last CO reading while

RANGE2

(HIGH) range was active to be

recorded.

06864D DCN7562

«
...
151
152
153
154
155
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Aaronia Pages: 47

Brand: Callaway Pages: 11

Brand: TA Instruments Pages: 7

Brand: Wagner Meters Pages: 17

Brand: G-Tek Pages: 83

Brand: Keysight Pages: 92

Brand: DeltaOHM Pages: 26

micro-TRI-gloss ?

Brand: BYK Pages: 174

Brand: Eno Scientific Pages: 47

Brand: Vega Pages: 44

Brand: Televes Pages: 2

Brand: Benetech Pages: 16

Brand: Westfalia Pages: 2

InnovaSonic 205i

Brand: Sierra Pages: 12

Brand: JGR Pages: 54

Brand: Fluke Biomedical Pages: 34

Ophir Spiricon BeamWatch Standard

Brand: MKS Pages: 20

Brand: Sonel Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands