TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 193 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Calibration Procedures

191

9.1.2.

DATA RECORDING DEVICES

A strip chart recorder, data acquisition system or digital data acquisition system should
be used to record data from the serial or analog outputs of the T300/T300M.

•

If analog readings are used, the response of the recording system should be
checked against a NIST traceable voltage source or meter.

•

Data recording devices should be capable of bi-polar operation so that negative
readings can be recorded.

•

For electronic data recording, the T300/T300M provides an internal data acquisition
system (DAS), which is described in detail in Section 7.

APICOM, a remote control program, is also provided as a convenient and powerful tool
for data handling, download, storage, quick check and plotting (see Section 7.2.1).

9.2.

MANUAL CALIBRATION

I

MPORTANT

I

MPACT ON

R

EADINGS OR

D

ATA

ZERO/SPAN CALIBRATION CHECKS VS. ZERO/SPAN CALIBRATION

Pressing the ENTR button during the following procedure resets the stored
values for OFFSET and SLOPE and alters the instrument’s Calibration.

This should ONLY BE DONE during an actual calibration of the T300/T300M.

NEVER press the ENTR button if you are only checking calibration. If you wish to
perform a calibration CHECK, do not press ENTR and refer to Section 9.2.2.

06864D DCN7562

«
...
191
192
193
194
195
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 4

Brand: Hanna Instruments Pages: 2

Orion Versa Star Pro Series

Brand: Thermo Scientific Pages: 4

SoundAdvisor NMS045

Brand: Larson Davis Pages: 64

Brand: Tenma Pages: 52

Brand: FuzzDog Pages: 6

sound SMART RLT Sport

Brand: VCA Pages: 36

Brand: Campbell Pages: 37

Brand: wtw Pages: 72

Rainbow RTI-Nano Series

Brand: Laserworld Pages: 25

Brand: RX Pages: 8

efector300 SM0510

Brand: IFM Electronic Pages: 45

Brand: LaserLine Pages: 11

Brand: 3nh Pages: 32

Brand: Crowcon Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands