TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 206 / 347

background image

Calibration Procedures

Teledyne API – Model T300/T300M CO Analyzer

204

9.3.3.3.

USE OF ZERO/SPAN VALVE WITH REMOTE CONTACT CLOSURE

Contact closures for controlling calibration and calibration checks are located on the rear
panel

CONTROL IN

connector. Instructions for setup and use of these contacts can be

found in Section 3.3.1.6.

When the appropriate contacts are closed for at least 5 seconds, the instrument switches
into zero, or span calibration mode and any internal zero/span valves installed will be
automatically switched to the appropriate configuration.

•

The remote calibration contact closures may be activated in any order.

•

It is recommended that contact closures remain closed for at least 10 minutes to
establish a reliable reading.

•

The instrument will stay in the selected mode for as long as the contacts remain
closed.

If contact closures are being used in conjunction with the analyzer’s AutoCal (see
Section 9.4) feature and the AutoCal attribute “

CALIBRATE”

is enabled, the

T300/T300M will not recalibrate the analyzer until the contact is opened. At this point,
the new calibration values will be recorded before the instrument returns to

Sample

Mode

.

If the AutoCal attribute “

CALIBRATE”

is disabled, the instrument will return to

Sample Mode

, leaving the instrument’s internal calibration variables unchanged.

9.4.

AUTOMATIC ZERO/SPAN CAL/CHECK (AUTOCAL)

The AutoCal system allows unattended periodic operation of the Z

ERO/SPAN

valve

options by using the T300/T300M Analyzer’s internal time of day clock. AutoCal
operates by executing

SEQUENCES

programmed by the user to initiate the various

calibration modes of the analyzer and open and close valves appropriately. It is possible
to program and run up to three separate sequences (

SEQ1

,

SEQ2

and

SEQ3

). Each

sequence can operate in one of three modes, or be disabled.

Table 9-2:

AUTOCAL Modes

MODE NAME

ACTION

DISABLED

Disables the Sequence.

ZERO

Causes the Sequence to perform a Zero calibration/check.

ZERO-SPAN

Causes the Sequence to perform a Zero point calibration/check followed by a
Span point calibration/check.

SPAN

Causes the Sequence to perform a Span concentration calibration/check only.

06864D DCN7562

«
...
204
205
206
207
208
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: 4iiii Pages: 3

Brand: dacell Pages: 22

Brand: Daewoo Pages: 2

ORBISPHERE 3624

Brand: Hach Ultra Pages: 12

Brand: QMI Pages: 54

Brand: X-Rite Pages: 50

Prestige Series

Brand: Ibanez Pages: 54

Brand: Yamaha Pages: 84

Brand: GARANT Pages: 368

Brand: YOSensi Pages: 27

Brand: Jula Pages: 9

LISST-PORTABLE XR

Brand: Sequoia Pages: 41

Brand: Solartron Mobrey Pages: 34

Brand: Interacoustics Pages: 54

Brand: PCB Piezotronics Pages: 10

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

Brand: Agilent Technologies Pages: 198

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands