TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 22 / 347

background image

Introduction, Features and Options

Teledyne API – Model T300/T300M CO Analyzer

20

Option

Option

Number

Description/Notes

Reference

Current Loop Analog
Outputs

Adds isolated, voltage-to-current conversion circuitry to the analyzer’s analog
outputs.

41

Can be configured for any output range between 0 and 20 mA.
May be ordered separately for any of the analog outputs.
Can be installed at the factory or retrofitted in the field.

Sections 3.3.1.3,
3.3.1.4, 5.9.1,
5.9.2 and 5.9.3.7

Parts Kits

Spare parts and expendables

42A

Expendables Kit

includes a recommended set of expendables for

one year of operation of this instrument including replacement sample
particulate filters.

Appendix B

45

Spare Parts Kit

includes spares parts for one unit.

Appendix B

Calibration Valves

Used to control the flow of calibration gases generated from external sources, rather
than manually switching the rear panel pneumatic connections.

50A

Ambient Zero and Ambient Span.

Sections 3.3.2.3
and 3.3.2.4

50B

Ambient Zero and Pressurized Span

Sections 3.3.2.5
and 3.3.2.6

50E

Zero Scrubber and Pressurized Span

Sections 3.3.2.7
and 3.3.2.8

50H

Zero Scrubber and Ambient Span

Sections 3.3.2.9
and 3.3.2.10

Communication Cables

For remote serial, network and Internet communication with the analyzer.

Type

Description

60A

RS-232

Shielded, straight-through DB-9F to DB-25M cable, about
1.8 m long. Used to interface with older computers or
code activated switches with DB-25 serial connectors.

Section 3.3.1.8
and 6.3

60B

RS-232

Shielded, straight-through DB-9F to DB-9F cable of about
1.8 m length.

Sections 3.3.1.8,
and 6.3

60C

Ethernet

Patch cable, 2 meters long, used for Internet and LAN
communications.

Sections 3.3.1.8
and 6.5

60D

USB

Cable for direct connection between instrument (rear
panel USB port) and personal computer.

Sections 3.3.1.8
and 6.6

Concentration Alarm Relay Issues warning when gas concentration exceeds limits set by user.

61

Four (4) “dry contact” relays on the rear panel of the instrument. This
relay option is different from and in addition to the “Contact Closures”
that come standard on all TAPI instruments.

Section 3.3.1.7

RS-232 Multidrop

Enables communications between host computer and up to eight analyzers.

62

Multidrop card seated on the analyzer’s CPU card.
Each instrument in the multidrop network requires this card and a
communications cable (Option 60B).

Sections 3.3.1.8
and 5.7.1

Second Gas Sensors

Choice of one additional gas sensor.

65A

Oxygen (O

2

) Sensor

• Sections 3.3.1.3

67A

Carbon Dioxide (CO

2

) Sensor

• Sections 3.3.1.3

06864D DCN7562

«
...
20
21
22
23
24
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: ABB Pages: 8

Brand: Bante Instruments Pages: 6

Brand: Tactical Controls Pages: 11

Brand: FarmChem Pages: 8

Brand: VEE GEE Pages: 2

Brand: IET Labs Pages: 114

Brand: Van Walt Pages: 12

Brand: MADDALENA Pages: 4

Brand: Macnaught Pages: 4

Brand: YOKOGAWA Pages: 2

ADMAG TI Series

Brand: YOKOGAWA Pages: 8

Brand: ETI Pages: 2

SF6 Portable Monitor

Brand: Bacharach Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: A&D Pages: 24

Brand: Heyuan Intelligence Pages: 14

Brand: Quadelectra Audioworx Pages: 12

xStorage Home Series

Brand: Eaton Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands