TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 241 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Troubleshooting and Service

239

Table 11-1: Warning Messages - Indicated Failures

WARNING

MESSAGE

FAULT CONDITION

POSSIBLE CAUSES

BENCH TEMP

WARNING

The optical bench temp is

controlled at 48

±

2

°

C.

Bad bench heater
Bad bench temperature sensor
Bad relay controlling the bench heater
Entire relay board is malfunctioning
I

2

C bus malfunction

BOX TEMP

WARNING

Box Temp is

< 5

°

C or > 48

°

C.

NOTE: Box temperature typically runs ~7

o

C warmer than ambient

temperature.
Poor/blocked ventilation to the analyzer.
Stopped exhaust-fan
Ambient temperature outside of specified range

CANNOT DYN

SPAN

Dynamic Span operation failed

Measured concentration value is too high or low.
Concentration slope value to high or too low

CANNOT DYN

ZERO

Dynamic Zero operation failed

Measured concentration value is too high.
Concentration offset value to high.

CONFIG

INITIALIZED

Configuration and Calibration data

reset to original Factory state.

Failed disk on module
User erased data

DATA INITIALIZED

Data Storage in DAS was erased

Failed disk on module
User cleared data

PHOTO TEMP

WARNING

PHT DRIVE is

>4800 mVDC

Failed IR photo-detector
Failed sync/demod board
IR photo-detector improperly attached to the sample chamber
Bench temp too high.

REAR BOARD NOT

DET

Motherboard not detected on power

up.

Warning only appears on serial I/O com port(s)
Front panel display will be frozen, blank or will not respond.
Massive failure of motherboard

RELAY BOARD

WARN

The CPU cannot communicate with

the Relay Board.

I

2

C bus failure

Failed relay board
Loose connectors/wiring

SAMPLE FLOW

WARN

Sample flow rate is < 500 cm

3

/min

or > 1000 cm

3

/min.

Failed sample pump
Blocked sample inlet/gas line
Dirty particulate filter
Leak downstream of critical flow orifice
Failed flow sensor/circuitry

SAMPLE PRES

WARN

Sample Pressure is <10 in-Hg or

> 35 in-Hg

Normally 29.92 in-Hg at sea level

decreasing at 1 in-Hg per 1000 ft of

altitude (with no flow – pump

disconnected).

If sample pressure is < 10 in-hg:
Blocked particulate filter
Blocked sample inlet/gas line
Failed pressure sensor/circuitry
If sample pressure is > 35 in-hg:
Pressurized sample gas. Install vent
Blocked vent line on pressurized sample/zero/span gas supply
Bad pressure sensor/circuitry

06864D DCN7562

«
...
239
240
241
242
243
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: E+E Elektronik Pages: 40

Brand: Oldham Pages: 34

Brand: WalkLAB Pages: 16

Brand: Gas Data Pages: 99

Brand: Magene Pages: 80

Brand: Trebs Pages: 44

Greenlee CLM-1000

Brand: Textron Pages: 36

micro-TRI-gloss ?

Brand: BYK Pages: 174

Brand: IDT Pages: 20

Brand: PASCO Pages: 2

Analite NEP-5000

Brand: Observator Instruments Pages: 103

Brand: 3M Pages: 168

Brand: Sensitech Pages: 2

Trimble Ranger 3

Brand: Badger Meter Pages: 20

Brand: A&D Pages: 38

Brand: STM Pages: 31

Brand: MEWOI Pages: 21

Brand: Haltech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands