TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 264 / 347

background image

Troubleshooting and Service

Teledyne API – Model T300/T300M CO Analyzer

262

11.5.4.

TOUCHSCREEN INTERFACE

Verify the functioning of the touchscreen by observing the display when pressing a
touchscreen control button. Assuming that there are no wiring problems and that the DC
power supplies are operating properly, if pressing a control button on the display does
not change the display, any of the following may be the problem:

•

The touchscreen controller may be malfunctioning.

•

The internal USB bus may be malfunctioning.

You can verify this failure by logging on to the instrument using APICOM or a terminal
program to any of the communications ports. If the analyzer responds to remote
commands and the display changes accordingly, the touchscreen interface may be faulty.

11.5.5.

LCD DISPLAY MODULE

Verify the functioning of the front panel display by observing it when power is applied
to the instrument. Assuming that there are no wiring problems and that the DC power
supplies are operating properly, the display screen should light and show the splash
screen with logo and other indications of its state as the CPU goes through its
initialization process.

11.5.6.

RELAY BOARD

The relay board PCA (P/N 04135) can be most easily checked by observing the
condition of the its status LEDs on the relay board, as described in Section 11.1.4.3, and
the associated output when toggled on and off through signal I/O function in the
diagnostic menu, see Section 11.1.3.

1. If the front panel display responds to button presses and D1 on the relay board is

NOT flashing then either the wiring between the touchscreen and the relay board is
bad, or the relay board is bad.

2. If D1 on the relay board is flashing and the status indicator for the output in question

(heater power, valve drive, etc.) toggles properly using the signal I/O function, then
the associated control device on the relay board is bad.

•

Several of the control devices are in sockets and can be easily replaced.

•

The table below lists the control device associated with a particular function:

Table 11-8:

Relay Board Control Devices

FUNCTION

CONTROL

DEVICE

IN SOCKET

Wheel Heater

K1

Yes

Bench Heater

K2

Yes

Spare AC Control

K3

Yes

IZS Valves

U4

Yes

IR Source Drive

U5

No

The IR source drive output can be verified by measuring the voltage at J16 with the IR
source disconnected. It should be 11.5± 0.5 VDC.

06864D DCN7562

«
...
262
263
264
265
266
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: ECC X-RAY Pages: 14

Brand: Kanomax Pages: 26

Brand: Macnaught Pages: 20

Brand: QuantAsylum Pages: 70

VOLUTANK Petro 3003

Brand: Bartec Pages: 10

Brand: A&D Pages: 68

Brand: LaserLiner Pages: 52

Brand: Veris Pages: 8

Brand: Palstar Pages: 37

Brand: LD Didactic Pages: 2

Brand: Lutron Electronics Pages: 13

Brand: UEi Pages: 5

Brand: MICRO-EPSILON Pages: 82

Brand: SBS Pages: 17

RLACS277RLACS29

Brand: Racelogic Pages: 10

Brand: A&D Pages: 2

Brand: Rinstrum Pages: 2

Brand: Harken Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands