TELEDYNE API T300 Operation Manual Download

Page: 277 / 347

Teledyne API – Model T300/T300M CO Analyzer

Troubleshooting and Service

275

11.6.3.2.

ADJUSTING THE SYNC/DEMODULATOR, CIRCUIT GAIN

To adjust the sync/demodulator circuit gain:

1. Make sure that the analyzer is turned on and warmed up.

2. Set the analyzer display to show the

STABIL

CO STB

test function.

3. Apply Zero Air to Sample Inlet of the analyzer.

4. Wait until the stability reading falls below 1.0 ppm.

5. Change the analyzer display to show the

CO MEAS.

6. Remove the Sync/Demod Housing

•

Remove the two mounting screws.

•

Carefully lift the housing to reveal the sync/demod PCA.

Figure 11-19: Location of Sync/Demod Housing Mounting Screws

7. Adjust potentiometer VR1 until

CO MEAS

reads 4500 mV ± 300 mV

VR1

Adjustment Made Here

Figure 11-20: Location of Sync/Demod Gain Potentiometer

06864D DCN7562

Summary of Contents for T300




























































































































































































































































































































































Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands

TELEDYNE API T300, Operation Manual

Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands