TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 286 / 347

background image

Theory of Operation

Teledyne API – Model T300/T300M CO Analyzer

284

I

NTERFERENCE AND

S

IGNAL TO

N

OISE

R

EJECTION

If an interfering gas, such as H

2

O vapor is introduced into the sample chamber, the

spectrum of the IR beam is changed in a way that is identical for both the reference and
the measurement cells, but without changing the ratio between the peak heights of

CO

MEAS

and

CO REF

. In effect, the difference between the peak heights remains the

same.

IR shining through both cells is

affected equally by interfering

gas in the Sample Chamber

M/R

is Shifted

Figure 12-5:

Effects of Interfering Gas on CO MEAS & CO REF

Thus, the difference in the peak heights and the resulting M/R ratio is only due to CO
and not to interfering gases. In this case, GFC rejects the effects of interfering gases and
so that the analyzer responds only to the presence of CO.

To improve the signal-to-noise performance of the IR photo-detector, the GFC Wheel
also incorporates an optical mask that chops the IR beam into alternating pulses of light
and dark at six times the frequency of the measure/reference signal. This limits the
detection bandwidth helping to reject interfering signals from outside this bandwidth
improving the signal to noise ratio.

The IR Signal as the Photo-

Detector sees it after being

chopped by the GFC Wheel

S

CO REF

CO

MEAS

Figure 12-6:

Chopped IR Signal

06864D DCN7562

«
...
284
285
286
287
288
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: 3nh Pages: 10

Brand: Larson Davis Pages: 193

Brand: Facom Pages: 116

Brand: Landis+Gyr Pages: 54

Brand: ICT Pages: 48

Brand: OfiTE Pages: 67

Brand: Bacharach Pages: 28

Brand: Bante Instruments Pages: 6

Brand: Omega Pages: 31

Brand: Parkside Pages: 120

Brand: SKF Pages: 12

micro-TRI-gloss ?

Brand: BYK Pages: 174

RHEASREG KLSW-3

Brand: S+S Regeltechnik Pages: 32

EA Heightmaster +

Brand: PROLEC Pages: 38

Brand: PTC Instruments Pages: 2

KS-PH-221-DELUXE

Brand: Kensington Pages: 14

Brand: Banner Pages: 4

Brand: Hanna Instruments Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands