manualshive.com logo in svg

TELEDYNE API T300, Operation Manual

The LG T300 User Manual is a comprehensive guide that details the features and functions of this sleek and versatile device. Easily download the manual for free from our website, providing you with all the necessary information to maximize your experience with the LG T300.

Share
Download
background image

Theory of Operation 

Teledyne API – Model T300/T300M CO Analyzer 

306 

12.5.2. 

CALIBRATION - SLOPE AND OFFSET 

Calibration of the analyzer is performed exclusively in software.   

During instrument calibration (see Section  9) the user enters expected values for zero 
and span via the front panel control buttonand commands the instrument to make 
readings of calibrated sample gases for both levels.  The readings taken are adjusted, 
linearized, and compared to the expected values.  With this information the software 
computes values for instrument slope and offset and stores these values in memory for 
use in calculating the CO concentration of the sample gas.   

The instrument slope and offset values recorded during the last calibration are available 
for viewing from the from the front panel (see Section 3.4.3). 

12.5.3. 

MEASUREMENT ALGORITHM  

Once the IR photo-detector signal is demodulated into 

CO MEAS

 and 

CO REF

 by the 

sync/demod board  and converted to digital data by the motherboard,  the T300/T300M 
analytical software calculates the ratio between 

CO MEAS

 and 

CO REF

.  This value is 

compared to a look-up table that is used, with interpolation, to linearize the response of 
the instrument.  The linearized concentration value is combined with calibration slope 
and offset values, then normalized for changes in sample gas pressure to produce the 
final CO concentration.  This is the value that is displayed on the instrument front panel 
display and is stored in memory by the analyzer’s DAS system. 

12.5.4. 

TEMPERATURE AND PRESSURE COMPENSATION 

Changes in pressure can have a noticeable, effect on the CO concentration calculation.  
To account for this, the T300/T300M  software includes a feature which allows the 
instrument to compensate for the CO calculations based on changes in ambient pressure.   

The TPC feature multiplies the analyzer’s CO concentration by a factor which is based 
on the difference between the ambient pressure of the sample gas normalized to standard 
atmospheric pressure.  As ambient pressure increases, the compensated CO 
concentration is decreased.   

12.5.5. 

INTERNAL DATA ACQUISITION SYSTEM (DAS) 

The  DAS  is designed to implement predictive diagnostics that stores trending data for 
users to anticipate when an instrument will require service.  Large amounts of data can 
be stored in non-volatile memory and retrieved in plain text format for further 
processing with common data analysis programs.  The DAS  has a consistent user 
interface in all Teledyne API analyzers.  New data parameters and triggering events can 
be added to the instrument as needed.   

Depending on the sampling frequency and the number of data parameters the DAS can 
store several months of data, which are retained even when  the instrument is powered 
off or a new firmware is installed.  The DAS permits users to access the data through the 
instrument’s front panel or the remote interface.  The latter can automatically download 
stored data for further processing.  For information on using the DAS, refer to Section 7

06864D DCN7562

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Parr Instrument Company 6300 Operating Instructions Manual preview
6300
Brand: Parr Instrument Company Pages: 130
jenway 6300 Operating Manual preview
6300
Brand: jenway Pages: 17
Flowmetrics 922-MFC Installation And Operating Instructions Manual preview
922-MFC
Brand: Flowmetrics Pages: 102
Baker Hughes Panametrics Aurora H2O User Manual preview
Panametrics Aurora H2O
Brand: Baker Hughes Pages: 92
phase II UTG-2650 Manual preview
UTG-2650
Brand: phase II Pages: 11
delta-mobrey Sentry Series Installation, Operation & Maintenance Instructions preview
Sentry Series
Brand: delta-mobrey Pages: 4
GREISINGER GOX 91 Brief Operating Manual preview
GOX 91
Brand: GREISINGER Pages: 4
Leutert MSI-4 Operating Instructions Manual preview
MSI-4
Brand: Leutert Pages: 8
Ditel DINOS DT203/NE Quick Installation Manual preview
DINOS DT203/NE
Brand: Ditel Pages: 2
LAUMAS W200-S Installation And User Manual preview
W200-S
Brand: LAUMAS Pages: 52
Hach Polymetron 9611sc PO4 3- Installation Manual preview
Polymetron 9611sc PO4 3-
Brand: Hach Pages: 476
A&D HF series Instruction Manual preview
HF series
Brand: A&D Pages: 35
Acrel AIM-T500 Installation And Operation Manual preview
AIM-T500
Brand: Acrel Pages: 16
REED R8100 Instruction Manual preview
R8100
Brand: REED Pages: 8
Endress+Hauser Proline Cubemass C 500 Technical Information preview
Proline Cubemass C 500
Brand: Endress+Hauser Pages: 108
ShinewayTech OPM-10V-S User Manual preview
OPM-10V-S
Brand: ShinewayTech Pages: 3
Servomex NanoTrace DF-745SG Operator'S Manual preview
NanoTrace DF-745SG
Brand: Servomex Pages: 94
R-Biopharm KOBRA CELL Instruction Manual preview
KOBRA CELL
Brand: R-Biopharm Pages: 24

Brands by name

Popular brands

Load more brands