TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 47 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Getting Started

45

3.3.1.7.

CONNECTING THE CONCENTRATION ALARM RELAY (OPTION 61)

The concentration alarm option is comprised of four (4) “dry contact” relays on the rear
panel of the instrument. This relay option is different from and in addition to the
“Contact Closures” that come standard on all Teledyne API instruments. Each relay has
3 pins: Normally Open (NO), Common (C), and Normally Closed (NC).

Figure 3-13:

Concentration Alarm Relay

Alarm 1

“System OK 2”

Alarm 2

“Conc 1”

Alarm 3

“Conc 2”

Alarm 4

“Range Bit”

“A

LARM

1”

R

ELAY

Alarm 1 which is “System OK 2” (system OK 1, is the status bit) is in the energized
state when the instrument is “OK” & there are no warnings. If there is a warning active
or if the instrument is put into the “DIAG” mode, Alarm 1 will change states. This
alarm has “reverse logic” meaning that if you put a meter across the Common &
Normally Closed pins on the connector you will find that it is OPEN when the
instrument is OK. This is so that if the instrument should turn off or lose power, it will
change states and you can record this with a data logger or other recording device.

“A

LARM

2”

R

ELAY

&

“A

LARM

3”

R

ELAY

Alarm 2 relay is associated with the “Concentration Alarm 1” set point in the software;
Alarm 3 Relay is associated with the “Concentration Alarm 2” set point in the software.

Alarm 2 Relay

CO Alarm 1 = xxx PPM

Alarm 3 Relay

CO

2

Alarm 2 = xxx PPM

Alarm 2 Relay

CO Alarm 1 = xxx PPM

Alarm 3 Relay

CO

2

Alarm 2 = xxx PPM

The Alarm 2 Relay will be turned on any time the concentration set-point is exceeded &
will return to its normal state when the concentration value goes back below the
concentration set-point.

Even though the relay on the rear panel is a NON-Latching alarm & resets when the
concentration goes back below the alarm set point, the warning on the front panel of the

06864D DCN7562

«
...
45
46
47
48
49
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Oakton Pages: 4

Brand: PAT Pages: 55

Brand: PAT Pages: 31

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Instrument Control System

Brand: Opus-Two Pages: 8

Brand: Interacoustics Pages: 60

Alta Site Survey Tool

Brand: Monnit Pages: 15

Brand: Kawai Pages: 36

Brand: Parker Pages: 16

Brand: Waterproof Pages: 51

Brand: JensPrima Pages: 20

SoundExpert LxT

Brand: Larson Davis Pages: 307

Brand: FuzzDog Pages: 6

Proline Promag 10D

Brand: Endress+Hauser Pages: 28

Brand: GREISINGER Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands