TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 70 / 347

background image

Getting Started

Teledyne API – Model T300/T300M CO Analyzer

68

If you are unfamiliar with the T300/T300M theory of operation, we recommend that you
read Section 12. For information on navigating the analyzer’s software menus, see the
menu trees described in Appendix A.

3.4.1.

STARTUP

After the electrical and pneumatic connections are made, an initial functional check is in
order. Turn on the instrument. The pump and exhaust fan should start immediately. The
display will briefly show a momentary splash screen of the Teledyne API logo and other
information during the initialization process while the CPU loads the operating system,
the firmware and the configuration data at the start of initialization.

The analyzer should automatically switch to Sample Mode after completing the boot-up
sequence and start monitoring CO gas. However, there is an approximately one hour
warm-up period before reliable gas measurements can be taken. During the warm-up
period, the front panel display may show messages in the Parameters field.

3.4.2.

WARNING MESSAGES

Because internal temperatures and other conditions may be outside the specified limits
during the analyzer’s warm-up period, the software will suppress most warning
conditions for 30 minutes after power up. If warning messages persist after the 60
minutes warm-up period is over, investigate their cause using the troubleshooting
guidelines in Section 11.

To view and clear warning messages, press:

Suppresses the

warning messages.

Press CLR to clear the current

message.

If more than one warning is

active, the next message will take

its place until all are cleared.

Once the last warning

has been cleared, the

RANGE function will

be displayed.

NOTE:

If a warning message persists after

several attempts to clear it, the message

may indicate a real problem and not an

artifact of the warm-up period.

SAMPLE SYSTEM RESET CO=XX.XX

TEST

CAL

MSG CLR SETUP

SAMPLE RANGE=XXX.X PPM CO=XX.XX

<TST TST>

CAL

MSG

SETUP

SAMPLE SYSTEM RESET CO=XX.XX

TEST

CAL

MSG

CLR

SETUP

STANDBY

RANGE=50.0 PPB CO=XX.XX

TEST

CAL

SETUP

MSG returns the active

warnings to the message

field.

Table 3-13 lists brief descriptions of the warning messages that may occur during start
up.

06864D DCN7562

«
...
68
69
70
71
72
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Valeport Pages: 27

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 101

Brand: jenway Pages: 52

Clavinova CVP-601

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 28

Brand: Daewoo Pages: 17

Brand: Hama Pages: 16

Brand: Trebs Pages: 44

Greenlee CLM-1000

Brand: Textron Pages: 36

Brand: janitza Pages: 128

Brand: PCE Health and Fitness Pages: 11

KINGFISHER PLUS+

Brand: semaphore Pages: 247

CR-2010 PRO Series

Brand: G-Tek Pages: 48

Brand: M-Audio Pages: 21

Brand: Z-Wave Pages: 5

Brand: Klein Tools Pages: 20

Brand: PKP Pages: 7

DMX Laser40 FScan

Brand: KAM Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands