TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 88 / 347

background image

Overview of Operating Modes

Teledyne API – Model T300/T300M CO Analyzer

86

4.3.3.

SECONDARY SETUP MENU (SETUP>MORE)

Table 4-5:

Secondary Setup Mode (SETUP>MORE) Features and Functions

MODE OR FEATURE

CONTROL

BUTTON

DESCRIPTION

MANUAL

SECTION

External Communication
Channel Configuration

COMM

Used to set up and operate the analyzer’s various serial
channels including RS-232,RS-485, modem communication,
Ethernet and/or USB.

System Status Variables

VARS

Used to view various variables related to the instruments current
operational status.

•

Changes made to any variable are not recorded in the

instrument’s memory until the

ENTR

button is pressed.

•

Pressing the

EXIT

button ignores the new setting.

System Diagnostic Features
and
Analog Output Configuration

DIAG

Used to access a variety of functions that are used to configure,
test or diagnose problems with a variety of the analyzer’s basic
systems.
Most notably, the menus used to configure the output signals
generated by the instruments Analog outputs are located here.

Alarm Limit Configuration

1

ALRM

Used to turn the instrument’s two alarms on and off as well as
set the trigger limits for each.

1

Alarm warnings only present when optional alarm package is activated.

I

MPORTANT

I

MPACT ON

R

EADINGS OR

D

ATA

Any changes made to a variable during the SETUP procedures are not
acknowledged by the instrument until the ENTR button is pressed. If the
EXIT button is pressed before the ENTR button, the analyzer will beep,
alerting the user that the newly entered value has not been accepted.

06864D DCN7562

«
...
86
87
88
89
90
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Yamaha Pages: 2

Brand: CONDTROL Pages: 8

Brand: Parkside Pages: 120

Vario 4 Typ 4.5.1

Brand: techem Pages: 142

Brand: SBS Pages: 17

Brand: Obvius Pages: 15

Brand: D-tect Systems Pages: 28

Brand: Oceanic Pages: 64

Brand: Maxtec Pages: 13

MON08 MULTILINK

Brand: P&E Microcomputer Systems Pages: 16

Brand: Anritsu Pages: 127

Brand: Lisle Pages: 8

Brand: JETI model Pages: 6

Brand: OHAUS Pages: 2

Brand: Hanna Instruments Pages: 72

Brand: K&M Pages: 2

Brand: netAlly Pages: 2

Brand: KROHNE Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands