TELEDYNE API T300 Operation Manual Download

Page: 112 / 347

Setup Menu

Teledyne API – Model T300/T300M CO Analyzer

110

5.9.3.

ANALOG I/O CONFIGURATION

The T300/T300M Analyzer comes equipped with four analog outputs.

•

The first two outputs (

A1 & A2)

carry analog signals that represent the currently

measured concentration of CO (see Section 5.4.1).

•

The third output (

) is only active if the analyzer is equipped with one of the

optional 2

gas sensors (e.g. O

or CO

•

The fourth output (

) outputs a signal that can be set to represent the current value

of one of several test functions (see Table 5-9).

Table 5-5 lists the analog I/O functions that are available in the T300/T300M Analyzer.

Table 5-5:

DIAG - Analog I/O Functions

SUB MENU

OUTPUT

CHANNEL

FUNCTION

AOUT

CALIBRATED

ALL

Initiates a calibration of the

and

analog output channels that

determines the slope and offset inherent in the circuitry of each output.

These values are stored and applied to the output signals by the CPU
automatically.

CONC_OUT_1

Sets the basic electronic configuration of the

output (CO Concentration).

There are four options:

•

RANGE

: Selects the signal type (voltage or current loop) and level of the

output.

•

REC

OFS

: Allows them input of a DC offset to let the user manually adjust

the output level.

•

AUTO CAL

: Enables / Disables the

AOUT CALIBRATED

feature.

•

CALIBRATED

: Performs the same calibration as

AOUT CALIBRATED

but on this one channel only.

CONC_OUT_2

•

Same as for CONC_OUT_1 but for analog channel

CONC_OUT_3

•

Same as for CONC_OUT_1 but for analog channel

but only if either the

optional O

or CO

sensors are installed.

TEST OUTPUT

•

Same as for CONC_OUT_1 but for analog channel

(TEST CHANNEL).

AIN

CALIBRATED

N/A

Initiates a calibration of the A-to-D Converter circuit located on the
Motherboard.

XIN1

.
.
.

XIN8

For each of 8 external analog input channels, shows the gain, offset,
engineering units, and whether the channel is to show up as a Test function.

Any changes made to

RANGE

REC_OFS

require recalibration of this output.

06864D DCN7562

Summary of Contents for T300




























































































































































































































































































































































Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands

TELEDYNE API T300, Operation Manual

Search results

Summary of Contents for T300

Reviews:

Related manuals for T300

Brands by name

Popular brands