TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 116 / 347

background image

Setup Menu

Teledyne API – Model T300/T300M CO Analyzer

114

5.9.3.2.

ANALOG OUTPUT CALIBRATION

Analog output calibration should to be carried out on first startup of the analyzer
(performed in the factory as part of the configuration process) or whenever recalibration
is required. The analog outputs can be calibrated automatically, either as a group or
individually, or adjusted manually.

In its default mode, the instrument is configured for automatic calibration of all
channels, which is useful for clearing any analog calibration warnings associated with
channels that will not be used or connected to any input or recording device, e.g.,
datalogger.

Manual calibration should be used for the 0.1V range or in cases where the outputs must
be closely matched to the characteristics of the recording device. Manual calibration
requires the AUTOCAL feature to be disabled.

Automatic calibration can be performed via the

CAL

button located inside The

AOUTS

CALIBRATION

submenu. By default, the analyzer is configured so that calibration of

analog outputs can be initiated as a group with the

AOUT CALIBRATION

command.

The outputs can also be calibrated individually, but this requires the AUTOCAL feature
be disabled.

5.9.3.3.

ENABLING OR DISABLING THE AUTOCAL FOR AN INDIVIDUAL ANALOG OUTPUT

To enable or disable the

AutoCal

feature for an individual analog output, elect the

ANALOG I/O CONFIGURATION

submenu (see Figure 5-3) then press:

06864D DCN7562

«
...
114
115
116
117
118
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Hach Pages: 28

Brand: jenway Pages: 18

HYGRASREG KH-30

Brand: S+S Regeltechnik Pages: 16

Clavinova CLP-311

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 15

Brand: Yamaha Pages: 3

Alto Horn, Baritone, Euphonium

Brand: Yamaha Pages: 22

Clavinova CLP-320

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 20

Brand: DAKOTA ULTRASONICS Pages: 38

Vigilantplant NFBU200-S Series

Brand: YOKOGAWA Pages: 24

Brand: horiba Pages: 117

Brand: Sequid Pages: 111

KEITHLEY 4200-CVU-PWR

Brand: Tektronix Pages: 6

SENSITRON SMART S

Brand: Halma Pages: 12

Brand: Quarton Pages: 2

Brand: Horiba Scientific Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands