TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 130 / 347

background image

Setup Menu

Teledyne API – Model T300/T300M CO Analyzer

128

5.9.7.

FLOW CALIBRATION

The flow calibration allows the user to adjust the values of the sample flow rates as they
are displayed on the front panel and reported through COMM ports to match the actual
flow rate measured at the sample inlet. This does not change the hardware measurement
of the flow sensors, only the software-calculated values. For details see Section 9.6.3.

5.9.8.

TEST CHAN OUTPUT

When activated, output channel

A4

can be used in the standard configuration to report

one of the test functions viewable from the SAMPLE mode display. (See also Section

5.9.8.1.

SELECTING A TEST CHANNEL FUNCTION FOR OUTPUT A4

The test functions available to be reported are listed in Table 5-9:

Table 5-9: Test Channels Functions available on the T300/T300M’s Analog Output

TEST CHANNEL

DESCRIPTION

ZERO

FULL SCALE

*

NONE

TEST CHANNEL IS TURNED OFF.

CO MEASURE

The demodulated, peak IR detector output
during the measure portion of the GFC Wheel
cycle.

0 mV

5000 mV

CO REFERENCE

The demodulated, peak IR detector output
during the reference portion of the GFC
Wheel cycle.

0 mV

5000 mV

SAMPLE PRESS

URE

The absolute pressure of the Sample gas as
measured by a pressure sensor located inside
the sample chamber.

0 "Hg

40 "Hg

SAMPLE FLOW

Sample mass flow rate as measured by the
flow rate sensor in the sample gas stream.

0 cm

3

/m

1000 cm

3

/m

SAMPLE TEMP

The temperature of the gas inside the sample
chamber.

0

°

C

70

°

C

BENCH TEMP

Optical bench temperature.

0

°

C

70

°

C

WHEEL TEMP

GFC Wheel temperature.

0

°

C

70

°

C

O

2

CELL TEMP

1

The current temperature of the O

2

sensor

measurement cell.

n

70

°

C

CHASSIS TEMP

The temperature inside the analyzer chassis.

0

°

C

70

°

C

PHT DRIVE

The drive voltage being supplied to the
thermoelectric coolers of the IR photo-
detector by the Sync/Demod Board.

0 mV

5000 mV

*

Maximum test signal value at full scale of test channel output.

1

When option installed.

Once a function is selected, the instrument not only begins to output a signal on the

analog output, but also adds

TEST

to the list of test functions viewable via the front

panel display.

06864D DCN7562

«
...
128
129
130
131
132
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: AccuMASTER Pages: 2

Brand: Bacharach Pages: 87

Brand: Xsens Pages: 4

Brand: Eastron Pages: 2

Brand: EASTERN INSTRUMENTS Pages: 3

Brand: Keithley Pages: 32

Brand: IFM Pages: 2

Professional Plus

Brand: YSI Pages: 28

Brand: Kawai Pages: 8

Brand: Bamo Pages: 17

Brand: H-Star Pages: 36

Amplitude T Series

Brand: OTOVATION Pages: 15

Brand: Trotec Pages: 3

Brand: Fluke Pages: 8

Brand: doble Pages: 78

Brand: EKF Pages: 32

Brand: Hioki Pages: 288

Brand: Kawai Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands