TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 141 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Communications Setup and Operation

139

6.5.1.

CONFIGURING ETHERNET COMMUNICATION MANUALLY (STATIC

IP ADDRESS)

To configure Ethernet communication manually:

1. Connect a cable from the analyzer’s Ethernet port to a Local Area Network (LAN) or

Internet port.

2. From the analyzer’s front panel touchscreen, access the Communications Menu

(SETUP>MORE>COMM).

3. Enter the Ethernet menu (INET), follow the setup sequence as shown in Figure 6-4,

and edit the Instrument and Gateway IP addresses and Subnet Mask to the desired
settings.

Alternatively, from the computer, enter the same information through an application
such as HyperTerminal.

Table 6-3 shows the default Ethernet configuration settings.

Table 6-3:

LAN/Internet Default Configuration Properties

PROPERTY

DEFAULT STATE

DESCRIPTION

DHCP

ON

This displays whether the DHCP is turned ON or OFF. Press
EDIT and toggle ON for automatic configuration after first
consulting network administrator.

INSTRUMENT IP

ADDRESS

This string of four packets of 1 to 3 numbers each (e.g.
192.168.76.55.) is the address of the analyzer itself.

GATEWAY IP

ADDRESS

0.0.0.0

Can only be edited when DHCP is set to OFF.
A string of numbers very similar to the Instrument IP address
(e.g. 192.168.76.1.) that is the address of the computer used
by your LAN to access the Internet.

SUBNET MASK

0.0.0.0

Can only be edited when DHCP is set to OFF.
Also a string of four packets of 1 to 3 numbers each (e.g.
255.255.252.0) that identifies the LAN to which the device is
connected.
All addressable devices and computers on a LAN must have
the same subnet mask. Any transmissions sent to devices
with different subnets are assumed to be outside of the LAN
and are routed through the gateway computer onto the
Internet.

TCP PORT

1

3000

This number defines the terminal control port by which the
instrument is addressed by terminal emulation software, such
as Internet or Teledyne API’s APICOM.

HOST NAME

[initially blank]

The name by which your analyzer will appear when
addressed from other computers on the LAN or via the
Internet. To change, see Section 6.5.3.

1

Do not change the setting for this property unless instructed to by Teledyne API’s Technical Support

personnel.

06864D DCN7562

«
...
139
140
141
142
143
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Masoneilan 12400 Series

Brand: Baker Hughes Pages: 81

Brand: Unior Pages: 2

Brand: Vaisala Pages: 83

Brand: DAKOTA ULTRASONICS Pages: 38

Instrument Control System

Brand: Opus-Two Pages: 8

Brand: RIDGID Pages: 18

Brand: SATO KEIRYOKI Pages: 2

Brand: Deprag Pages: 28

Vigilant Plant MR20000

Brand: YOKOGAWA Pages: 230

Multifunction Compensator

Brand: Halcyon Pages: 20

60 VioLab Series

Brand: XS Instruments Pages: 41

Brand: Toner Pages: 7

Brand: Stabila Pages: 14

Brand: b&o Pages: 32

Mini HD Recorder

Brand: Green Feathers Pages: 8

Brand: Smartwares Pages: 2

DUSTHUNTER SB30

Brand: SICK Pages: 72

Brand: Amazing Machinery Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands