TELEDYNE API T300 Operation Manual Download | Manualshive

Page: 167 / 347

background image

Teledyne API – Model T300/T300M CO Analyzer

Data Acquisition System (DAS) and APICOM

165

7.1.5.

EDITING DAS TRIGGERING EVENTS

Triggering events define when and how the DAS records a measurement of any given
data channel. Triggering events are firmware-specific and are listed in Appendix A-5.
The most commonly used triggering events are:

•

ATIMER

: Sampling at regular intervals specified by an automatic timer. Most

trending information is usually stored at such regular intervals, which can be
instantaneous or averaged.

•

EXITZR

,

EXITSP

, and

SLPCHG

(exit zero, exit span, slope change): Sampling at

the end of (irregularly occurring) calibrations or when the response slope changes.
These triggering events create instantaneous data points, e.g., for the new slope
and offset (concentration response) values at the end of a calibration. Zero and
slope values are valuable to monitor response drift and to document when the
instrument was calibrated.

•

WARNINGS:

Some data may be useful when stored if one of several warning

messages appears such as

WTEMPW

(GFC Wheel temperature warning). This is

helpful for troubleshooting by monitoring when a particular warning occurrs.

To edit the list of data parameters associated with a specific data channel, follow the
instruction shown in Section 7.1.4 then press:

Starting at the

EDIT CHANNEL MENU

SETUP X.X

0) CONC: ATIMER 1, 800

PREV NEXT

INS

DEL

EDIT

PRNT

EXIT

SETUP X.X

NAME: CONC

SET>

EDIT

EXIT

Continue pressing

SET>

until ...

SETUP X.X

EVENT:ATIMER

<SET

SET>

EDIT

EXIT

Toggle these

buttons to cycle

through the list of

available trigger

event.

EXIT

discards the new

setting.

ENTR

accepts the

new setting.

EVENT:ATIMER

PREV NEXT

ENTR

EXIT

06864D DCN7562

«
...
165
166
167
168
169
...
»

Summary of Contents for T300




























































































































































































































































































































































Reviews:

No comments

Related manuals for T300

Brand: Danfoss Pages: 8

BML SL1-ALZ-ZZ Series

Brand: Balluff Pages: 26

Brand: Hama Pages: 6

Brand: Kathrein Pages: 10

Brand: Teledyne Hastings Instruments Pages: 54

Brand: Kobold Pages: 55

Brand: Autometers Systems Pages: 16

Brand: ACE INSTRUMENTS Pages: 6

Brand: ICP DAS USA Pages: 71

Brand: CONDTROL Pages: 11

Brand: Milwaukee Pages: 17

Brand: Hach Pages: 2

Brand: Ocean Reef Pages: 24

BlueForce Smart

Brand: CAME Pages: 24

Brand: National Instruments Pages: 40

Brand: Hioki Pages: 16

Brand: Oakton Pages: 12

Nunes Instruments Propeller Type Water Current...

Brand: V-tech Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands